HardLabs

ESP32 laptop strip.kicad

collaborative-music-lab·ESP_MIDI·PCB/Kicad/ESP32_laptop-strip.kicad_pcb/ESP32_laptop-strip.kicad_pcb.kicad_pcb

ESP32 laptop strip.kicad PCB layout, top view — open source ESP32 board by collaborative-music-lab
Simulate this board

About the ESP32 laptop strip.kicad PCB

ESP32 laptop strip.kicad is an open source ESP32 PCB design by collaborative-music-lab, published on GitHub. It is a 2-layer board measuring 224.5 × 25 mm, with 12 components from 7 distinct parts.

Its main chip is the Wifiduino-ESP32S3-SMD, from the ESP32 family. Other key parts include the 74AHCT1G125. By type, the board carries 6 capacitors, 2 ICs, 2 switches, 1 connector and 1 resistor.

It belongs with the audio, iot & wireless and sensors designs in this gallery.

From the project

ESP32-s3 midi controller

1. The main PCB, with the ESP32 pre-soldered 2. 4 potentiometers, 2 to place on the PCB and two additional off-board potentiometers with small pcbs. 3. 4 Arcade Buttons 4. An LSM6DS3 IMU breakout board 5. An RGB LED and resistors

Make sure get your enclosure drilled for your faceplate before you mount your PCB to the faceplate in step 9!!!

1. Place two potentiometers on the PCB. Make sure they are flat. It is a good idea to place the potentiometers on a faceplate to make sure they are aligned. Solder the potentiometers in place. the potentiometers go on the opposite side of the PCB from the…

Main components on the ESP32 laptop strip.kicad

74AHCT1G125

ESP32 laptop strip.kicad bill of materials (BOM)

12 components, 7 distinct parts.

QtyPartRefs
1
74AHCT1G125
U1
1
~
U2
1
Conn_01x03_Pin
J1
2
RotaryEncoder
SW9, SW10
5
10nF
C1, C3, C4, C5, C6
1
0.1uF
C2
1
R_Small
R1

ESP32 laptop strip.kicad design files

The KiCad project lives in the collaborative-music-lab/ESP_MIDI repository on GitHub; these links point at the commit this page was built from.

ESP32 laptop strip.kicad: common questions

What microcontroller does the ESP32 laptop strip.kicad use?

The ESP32 laptop strip.kicad is built around the Wifiduino-ESP32S3-SMD, from the ESP32 family.

How big is the ESP32 laptop strip.kicad PCB?

The ESP32 laptop strip.kicad measures 224.5 × 25 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ESP32 laptop strip.kicad?

12 components, from 7 distinct parts. The full bill of materials is listed on this page.

Where can I download the ESP32 laptop strip.kicad design files?

From the collaborative-music-lab/ESP_MIDI repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the ESP32 laptop strip.kicad design in my own project?

The repository has no license, so all rights stay with collaborative-music-lab. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the ESP32 laptop strip.kicad without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ESP_MIDI

Similar boards