THE-BUTTON
couchpotatoe1234·THE-BUTTON·THE BUTTON PCB/THE BUTTON.kicad_pcb
About the THE-BUTTON PCB
THE-BUTTON is an open source ESP32 PCB design by couchpotatoe1234, published on GitHub. It is a 2-layer board measuring 38.5 × 49.8 mm, with 11 components from 10 distinct parts.
Its main chip is the XIAO-ESP32-C3-DIP, from the ESP32 family. Other key parts include the MCP1700x-120xxTO. By type, the board carries 4 capacitors, 2 ICs, 2 switches, 1 battery holder, 1 diode and 1 resistor.
It belongs with the keyboards and iot & wireless designs in this gallery.
From the project
A Macropad with one singular button. Used for an emergency button to close a tab when a parent is coming perhaps...
Main components on the THE-BUTTON
THE-BUTTON bill of materials (BOM)
11 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-DIP | XIAO-ESP32-C3-DIP | U1 |
| 1 | MCP1700x-120xxTO | TO-92_Inline | U2 |
| 1 | Battery_Cell | PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1 |
| 1 | SW_SPST | SW3x1_L101011ML04Q_CNK | SW3 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 2 | 1uF | C_Disc_D5.1mm_W3.2mm_P5.00mm | C1, C2 |
| 1 | 100uF | PCAP_8x11_5-THRU-ELECT_NCA | C3 |
| 1 | 0.1uF | K104K15X7RF5TL2_VIS | C4 |
| 1 | 330Ω | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
THE-BUTTON design files
The KiCad project lives in the couchpotatoe1234/THE-BUTTON repository on GitHub; these links point at the commit this page was built from.
THE-BUTTON: common questions
What microcontroller does the THE-BUTTON use?
The THE-BUTTON is built around the XIAO-ESP32-C3-DIP, from the ESP32 family.
How big is the THE-BUTTON PCB?
The THE-BUTTON measures 38.5 × 49.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the THE-BUTTON?
11 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the THE-BUTTON design files?
From the couchpotatoe1234/THE-BUTTON repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the THE-BUTTON design in my own project?
The repository has no license, so all rights stay with couchpotatoe1234. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the THE-BUTTON without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k