Duckhouse
cstapels·duckhouse·duckboard/DuckControlBoard/duckboardAI.kicad_pcb
About the Duckhouse PCB
Duckhouse is an open source ESP32 PCB design by cstapels, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 103 × 93.5 mm, with 60 components from 32 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. By type, the board carries 25 resistors, 17 connectors, 13 capacitors, 2 transistors, 1 IC and 1 fuse.
From the project
controller for the duck house
Main components on the Duckhouse
Duckhouse bill of materials (BOM)
60 components, 32 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DevKitC | ESP32-DevKitC | U1 |
| 1 | 27P04 | TO-220-3_Horizontal_TabUp | Q1 |
| 1 | 30N06L | TO-220-3_Horizontal_TabUp | Q2 |
| 1 | BATTERY | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J1 |
| 1 | 5V BUCK | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | LIFT BTS7960 | PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | DOOR BTS7960 | PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | LIFT CLOSE | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J6 |
| 1 | LIFT OPEN | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J7 |
| 1 | DOOR CLOSE | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J8 |
| 1 | DOOR OPEN | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J9 |
| 1 | Tank Level | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J10 |
| 1 | 5V OUT | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J11 |
| 1 | PUMP_CONTROL | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J12 |
| 1 | DOOR_OPEN_LIMIT | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J14 |
| 1 | DOOR_CLOSE_LIMIT | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J15 |
| 1 | LIFT_CLOSE_LIMIT | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J16 |
| 1 | Conn_01x02 | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J17PhotoSensor1 |
| 2 | R_Potentiometer | Potentiometer_Piher_T-16L_Single_Vertical_Hole | P1, P2 |
| 1 | 8A | Fuseholder_Cylinder-5x20mm_Schurter_0031_8201_Horizontal_Open | F1 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BLUE SMD3528 | LED_Everlight-SMD3528_3.5x2.8mm_67-21ST | D1 |
| 1 | 100uF 35V | C_0805_2012Metric | C1 |
| 1 | 1uF 35V | C_0805_2012Metric | C2 |
| 10 | 100nF | C_0805_2012Metric | C3, C6, C7, C8, C9, C10, C11, C12 +2 |
| 1 | 100 nF | C_0805_2012Metric | C5 |
| 15 | 10k | R_0603_1608Metric | R1, R2, R9, R10, R11, R12, R13, R14 +7 |
| 2 | 470 | R_0603_1608Metric | R3, R25 |
| 1 | 2M 1% | R_0603_1608Metric | R4 |
| 1 | 100k 1% | R_0603_1608Metric | R5 |
| 4 | 470R | R_0603_1608Metric | R6, R7, R8, R21 |
| 1 | 120R | R_0603_1608Metric | R16 |
| 1 | 1k | R_0603_1608Metric | R17 |
Duckhouse design files
The KiCad project lives in the cstapels/duckhouse repository on GitHub; these links point at the commit this page was built from.
Duckhouse: common questions
What microcontroller does the Duckhouse use?
The Duckhouse is built around the ESP32-DevKitC, from the ESP32 family.
How big is the Duckhouse PCB?
The Duckhouse measures 103 × 93.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Duckhouse?
60 components, from 32 distinct parts. The full bill of materials is listed on this page.
Where can I download the Duckhouse design files?
From the cstapels/duckhouse repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Duckhouse design in my own project?
Yes, under the terms of its GPL-3.0 license, which cstapels chose for the repository.
Can I test firmware for the Duckhouse without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k