WeatherSensor
d3wzs·weatherSensor·PCB-Files/Weather Station.kicad_pcb
About the WeatherSensor PCB
WeatherSensor is an open source ESP32 PCB design by d3wzs, published on GitHub. It is a 2-layer board measuring 120 × 60 mm, with 7 components from 6 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. Other key parts include the DHT22 and TFT_320x240. By type, the board carries 3 ICs and 2 switches.
It belongs with the sensors designs in this gallery.
From the project
This is a project that I made for Hack Clubs Half Life. It is a relatively compact weather sensor that can detect outside weather from inside. The code is far from complete but I find coding much easier when I can troubleshoot and test it with what im coding, so I'll finish it on
This is a project that I made for Hack Clubs Half Life. It is a relatively compact weather sensor that can detect outside weather from inside. The code is far from complete but I find coding much easier when I can troubleshoot and test it with what im coding, so I'll finish it once its been built.
- Indoor Temp Sensing - DHT22 - Outdoor Temp Sensing - DS18B20 - 2.8" TFT Display - Interaction - Low Profile Switches - Light Sensing - SAMIROB VEML7700 Ambient Light Sensor - Custom PCB - Custom Case
Main components on the WeatherSensor
WeatherSensor bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32_30pin | U1 |
| 1 | DHT22 | XDCR_DHT22 | U2 |
| 1 | TFT_320x240 | TFT-320x240 | U3 |
| 2 | SW_Push | Kailh Choc Low-Profile Switches | SW1, SW2 |
| 1 | Conn_01x05_Pin | PinHeader_1x05_P2.54mm_Vertical | lightsensor1 |
| 1 | Conn_01x03_Pin | FanPinHeader_1x03_P2.54mm_Vertical | outdoortempsensor1 |
WeatherSensor design files
The KiCad project lives in the d3wzs/weatherSensor repository on GitHub; these links point at the commit this page was built from.
WeatherSensor: common questions
What microcontroller does the WeatherSensor use?
The WeatherSensor is built around the ESP32_30pin, from the ESP32 family.
How big is the WeatherSensor PCB?
The WeatherSensor measures 120 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the WeatherSensor?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the WeatherSensor design files?
From the d3wzs/weatherSensor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the WeatherSensor design in my own project?
The repository has no license, so all rights stay with d3wzs. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the WeatherSensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k