AetherArray
DanielMBouyou·AetherArray·hardware/rev-a/aetherarray-reva.kicad_sch
About the AetherArray PCB
AetherArray is an open source PCB design by DanielMBouyou, published on GitHub. It is a board, with 132 components from 32 distinct parts.
Other key parts include the PE4259-63, AD8318ACPZ and MCP9808T-E/MS. By type, the board carries 39 capacitors, 32 ICs, 13 test points, 12 resistors and 6 connectors.
It belongs with the test & measurement and rf & radio designs in this gallery.
From the project
Research notebook on phased array calibration: channel errors, mutual coupling, inverse problems, and how few physical measurements are actually needed.
- Status: captured, electrical rule check clean, ready for review - Last reviewed: 2026-09-28
This is the schematic for the board chosen in decisions/0003-rev-a-rf-architecture.md. The layout hasn't started, and that decision doesn't allow it yet.
rf-channel.kicadsch` is one hierarchical sheet, used four times. There's no second copy that could drift out of step, so the four channels match because of how the files are built, not because somebody edited carefully. It's checked anyway: after generation, the net layout of the four channels is compared, and it has to match.
Main components on the AetherArray
AetherArray bill of materials (BOM)
132 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 29 | PE4259-63 | U101, U102, U103, U104, U105, U106, U107, U201 +21 | |
| 1 | AD8318ACPZ AD8318 | U901 | |
| 2 | MCP9808T-E/MS MCP9808 | U902, U903 | |
| 1 | SMA_EL0 | J900 | |
| 1 | SMA_EL1 | J901 | |
| 1 | SMA_EL2 | J902 | |
| 1 | SMA_EL3 | J903 | |
| 1 | SMA_COMMON | J904 | |
| 1 | NUCLEO_G0_IF | J905 | |
| 4 | REF_45 | TL101, TL201, TL301, TL401 | |
| 4 | DLY_45 | TL102, TL202, TL302, TL402 | |
| 4 | REF_90 | TL103, TL203, TL303, TL403 | |
| 4 | DLY_90 | TL104, TL204, TL304, TL404 | |
| 4 | REF_180 | TL105, TL205, TL305, TL405 | |
| 4 | DLY_180 | TL106, TL206, TL306, TL406 | |
| 6 | QW_70R7 | TL901, TL902, TL903, TL904, TL905, TL906 | |
| 4 | TP_RF_IN | TP101, TP201, TP301, TP401 | |
| 4 | TP_RF_OUT | TP102, TP202, TP302, TP402 | |
| 1 | TP_VOUT | TP900 | |
| 1 | TP_TEMP | TP901 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TP_5V | TP902 | |
| 1 | TP_3V3 | TP903 | |
| 1 | TP_GND | TP904 | |
| 35 | 100NF 100nF | C101, C102, C103, C104, C105, C106, C107, C201 +27 | |
| 2 | 100PF 100pF | C901, C902 | |
| 1 | 1NF 1nF | C904 | |
| 1 | 220PF 220pF | C906 | |
| 4 | 50R | R101, R201, R301, R401 | |
| 3 | 100R | R900, R901, R902 | |
| 1 | 18K 18k | R903 | |
| 2 | 1k | R904, R905 | |
| 2 | 4K7 4k7 | R906, R907 |
AetherArray design files
The KiCad project lives in the DanielMBouyou/AetherArray repository on GitHub; these links point at the commit this page was built from.
AetherArray: common questions
How many components are on the AetherArray?
132 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the AetherArray design files?
From the DanielMBouyou/AetherArray repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the AetherArray design in my own project?
The repository has no license, so all rights stay with DanielMBouyou. Use it as a reference, and ask the author before reusing the design.
Similar boards
StackLink
gusmanb
52.3 × 10.5 mm5 parts2LGPL-3.05.0kLevelShifter
gusmanb
28.3 × 39.8 mm21 parts2LGPL-3.05.0kAnalyzerBoxPCB fork
gusmanb
52.7 × 47.9 mm54 parts4LGPL-3.05.0kRadioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Hat
pa3gsb
65 × 56 mm81 parts2LNo license675