13 open source boards using the MCP9808T-E/MS
Real designs built with the MCP9808T-E/MS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Dynossat edu obc
BHDynamics
42 × 42 mm52 parts4LCERN-OHL-1.214SCALES Leviathan V2
BroncoSpace-Lab
100 × 100 mm415 parts6LNo license6RP2040/RP2350
Billee hardware-2027
BILLEE-BroncoSTAR
240 × 90.5 mm265 parts4LMIT1STM32
Plant monitor
PimentoFr
50 × 74 mm168 parts4LNo license0ESP32
Vaporizer
itspolly
73.8 × 73.9 mm108 parts2LUnlicense0ESP32
Puck
zachariahsharma
29.7 × 72.5 mm20 parts4LNo license0- schematic only · 132 parts
AetherArray
DanielMBouyou
132 partsNo license0 Nordic nRF
Temperature
urlenbayev
48 × 44.2 mm15 parts2LGPL-3.00I2c sensor
devkyber
45 × 35 mm13 parts2LNo license0Battery Board
aati106
91.9 × 201.7 mm61 parts4LNo license2EPS Scales RevG
BroncoSpace-Lab
100 × 100 mm176 parts4LNo license6ESP32
Esp32 mcp9808
HeyPCB
30 × 48 mm24 parts4LCERN-OHL-S-2.00Mcp9808-breakout
embedrapp
18 × 15 mm6 parts2LMIT1
How designs wire the MCP9808T-E/MS
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the MCP9808T-E/MS connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 10 of 11 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 9 of 11 designs, most often 4.7 kΩ (then 10 kΩ).
- The VDD pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF.
- The A1 pin is tied to GND on 8 of 11 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SDApin 1 | Connected to: The microcontroller 45%, a connector 36%, MCP9808T-E/MS 27% |
|
| SCLpin 2 | Connected to: The microcontroller 45%, a connector 36%, MCP9808T-E/MS 27% |
|
| ALERTpin 3 | Connected to: A connector 27%, the microcontroller 27% · not connected 36% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| A2pin 5 | Connected to: GND 64% · a signal 27% | — |
| A1pin 6 | Connected to: GND 73% · a signal 27% | — |
| A0pin 7 | Connected to: GND 64% · a signal 27% | — |
| VDDpin 8 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dynossat edu obc by BHDynamics, EPS Scales RevG by BroncoSpace-Lab, Battery Board by aati106 and Billee hardware-2027 by BILLEE-BroncoSTAR.
The MCP9808T-E/MS in open source designs
The gallery holds 13 open source boards using the MCP9808T-E/MS from 12 GitHub repositories; a typical one measures about 49 × 73.2 mm and carries around 61 components.
67% use four copper layers or more, and 46% carry an open source license.
The most starred is Dynossat edu obc by BHDynamics.
Parts used alongside the MCP9808T-E/MS
Microcontrollers on boards using the MCP9808T-E/MS
What boards using the MCP9808T-E/MS are built for
MCP9808T-E/MS: common questions
Where can I find a MCP9808T-E/MS reference design?
Each of the 13 boards on this page is a real design using the MCP9808T-E/MS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP9808T-E/MS SDA pin?
The SDA pin has a pull-up to 3.3V on 10 of 11 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 11 open source designs using the MCP9808T-E/MS.
What pull-up resistor is used on the MCP9808T-E/MS SCL pin?
The SCL pin has a pull-up to 3.3V on 9 of 11 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 11 open source designs using the MCP9808T-E/MS.
What decoupling capacitors do designs use on the MCP9808T-E/MS VDD pin?
The VDD pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF. Counted from the KiCad layouts of 11 open source designs using the MCP9808T-E/MS.
What parts are used alongside the MCP9808T-E/MS?
The AP2112K-3.3TRG1, TCA4307DGKR and TXS0108EPWR appear in the most repositories here.
Which microcontrollers do boards using the MCP9808T-E/MS use?
Most are built on ESP32 (3), Nordic nRF (1), RP2040/RP2350 (1) and Microchip SAM (1).
How big is a typical board using the MCP9808T-E/MS?
The median is 49 × 73.2 mm, and 33% are two-layer designs.
What is the most popular open source board using the MCP9808T-E/MS?
By GitHub stars, Dynossat edu obc by BHDynamics, with 14 stars.
Can I simulate one of these boards using the MCP9808T-E/MS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.