Desk controller psu

DanteWinters·desk-controller-psu

Desk controller psu PCB layout, top view — open source ESP32 board by DanteWinters

About the Desk controller psu PCB

Desk controller psu is an open source ESP32 PCB design by DanteWinters, published on GitHub. It is a 2-layer board measuring 160 × 110 mm, with 26 components from 22 distinct parts.

Its main chip is the ESP32 DevKit V1 (30 pin), from the ESP32 family. Other key parts include the 12V->5V buck module and PC817. By type, the board carries 12 connectors, 5 ICs, 5 resistors, 2 diodes and 2 capacitors.

It belongs with the iot & wireless and power & battery designs in this gallery.

From the project

A single PCB that tidies up the electronics in my desk stand. It distributes 12 V and 5 V power and lets an ESP32 (through Home Assistant) press the buttons on two HDMI switches and a USB switch.

A single PCB that tidies up the electronics in my desk stand. It distributes 12 V and 5 V power and lets an ESP32 (through Home Assistant) press the buttons on two HDMI switches and a USB switch.

Status: v1 design, not yet built or tested in hardware. ERC and DRC are clean in KiCad 10.

Open DeskController.kicadpro in KiCad 10** or later. All other footprints come from the standard KiCad libraries.

Desk controller psu, from the project README
From the project README

Main components on the Desk controller psu

Desk controller psu bill of materials (BOM)

26 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32 DevKit V1 (30 pin)
U1
1
12V->5V buck module
U2
3
PC817
U3, U4, U5
1
12V IN (from PSU)
J1
1
12V OUT USB hub
J2
1
12V OUT USB charger
J3
1
12V OUT spare
J4
1
5V USB HDMI switch 1
J5
1
5V USB HDMI switch 2
J6
1
5V USB USB switch
J7
1
SW1 button (E, C)
J8
1
SW2 button (E, C)
J9
1
SW3 button (E, C)
J10
1
Expansion / display header
J11
1
5V aux (display power)
J12
1
12V (green)
D1
1
5V (green)
D2
1
470uF 25V
C1
1
470uF 10V
C2
1
2k2
R1
Show 2 more
QtyPartRefs
1
1k
R2
3
220
R3, R4, R5

Desk controller psu design files

The KiCad project lives in the DanteWinters/desk-controller-psu repository on GitHub; these links point at the commit this page was built from.

Desk controller psu: common questions

What microcontroller does the Desk controller psu use?

The Desk controller psu is built around the ESP32 DevKit V1 (30 pin), from the ESP32 family.

How big is the Desk controller psu PCB?

The Desk controller psu measures 160 × 110 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Desk controller psu?

26 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Desk controller psu design files?

From the DanteWinters/desk-controller-psu repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Desk controller psu design in my own project?

The repository has no license, so all rights stay with DanteWinters. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Desk controller psu without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards