Eckplatine EP-1
DesignStraub·ringwheel-hybrid-drone·electronics/Eckplatine/Eckplatine.kicad_pcb
About the Eckplatine EP-1 PCB
Eckplatine EP-1 is an open source PCB design by DesignStraub, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 24 × 24 mm, with 8 components from 7 distinct parts.
Other key parts include the C2071868. By type, the board carries 3 capacitors, 2 connectors, 2 resistors and 1 IC.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
A 5-inch FPV drone whose prop ducts fold down and become wheels. Design study in Fusion 360 and KiCad, CC BY-NC-SA 4.0.
A 5-inch FPV quadcopter that lands, folds its four ducts down by 90° and drives away on them. Each duct ring has a tread and turns into a wheel. The same four motors fly the drone and drive the wheels.
Video: Watch the 55-second walkthrough on YouTube or download it in 16:9 as MP4 (17 MB)
- Folding: Each arm ends in a hinge. A small N20 gear motor turns it through a self-locking brass worm drive (1:30). An AS5600 magnetic sensor reads the angle, and fixed end stops limit the travel to 0° (flight) and 90° (drive). - Ring = wheel: The duct around each 5.1" propeller has a TPU tread and runs…

Main components on the Eckplatine EP-1
Eckplatine EP-1 bill of materials (BOM)
8 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C2071868 AS5600-ASOM | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | vom Hybrid-Controller | JST_GH_SM08B-GHS-TB_1x08-1MP_P1.25mm_Horizontal | J1 |
| 1 | zum Radmodul (Muffensensor) | JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | J2 |
| 1 | 100nF | C_0603_1608Metric | C1 |
| 1 | 100nF | C_0402_1005Metric | C2 |
| 1 | 1uF | C_0402_1005Metric | C3 |
| 2 | 4.7k | R_0402_1005Metric | R1, R2 |
Eckplatine EP-1 design files
The KiCad project lives in the DesignStraub/ringwheel-hybrid-drone repository on GitHub; these links point at the commit this page was built from.
Eckplatine EP-1: common questions
How big is the Eckplatine EP-1 PCB?
The Eckplatine EP-1 measures 24 × 24 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Eckplatine EP-1?
8 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Eckplatine EP-1 design files?
From the DesignStraub/ringwheel-hybrid-drone repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Eckplatine EP-1 design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
More boards in ringwheel-hybrid-drone
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k