ESP32 Base
DominikNeugebauer·PCB·ESP32_Base/ESP32_Base/ESP32_Base.kicad_pcb
About the ESP32 Base PCB
ESP32 Base is an open source ESP32 PCB design by DominikNeugebauer, published on GitHub. It is a 2-layer board measuring 62.5 × 35 mm, with 32 components from 15 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R2, from the ESP32 family. By type, the board carries 13 resistors, 11 capacitors and 6 diodes.
From the project
All of my pcb projects i have made so far
ESP32 Base bill of materials (BOM)
32 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | AMS1117 |
| 1 | ESP32-S3-WROOM-1-N16R2 | ESP32_S3_WROOM_N16R2_CUSTOM | ESP32-S3-WROOM |
| 1 | 1N5819HW-7-F | SOD3715X145N | D1 |
| 3 | LESD5D5.0CT1G | TVS_LESD5D5.0CT1G | D2, D3, D4 |
| 1 | PWR | LED_1206_3216Metric | D5 |
| 1 | LED | LED_1206_3216Metric | D7 |
| 4 | 10uF | C_0603_1608Metric | C1, C2, C4, C13 |
| 2 | 0u1F | C_0603_1608Metric | C3, C5 |
| 4 | 0.1uF | C_0603_1608Metric | C6, C10, C11, C14 |
| 1 | 1uF | C_0603_1608Metric | C12 |
| 2 | 5k1 | R_0603_1608Metric | R1, R2 |
| 2 | 75 | R_0603_1608Metric | R3, R11 |
| 3 | 10k | R_0603_1608Metric | R4, R5, R7 |
| 3 | 100 | R_0603_1608Metric | R6, R8, R9 |
| 3 | 33 | R_0603_1608Metric | R10, R12, R13 |
ESP32 Base design files
The KiCad project lives in the DominikNeugebauer/PCB repository on GitHub; these links point at the commit this page was built from.
ESP32 Base: common questions
What microcontroller does the ESP32 Base use?
The ESP32 Base is built around the ESP32-S3-WROOM-1-N16R2, from the ESP32 family.
How big is the ESP32 Base PCB?
The ESP32 Base measures 62.5 × 35 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32 Base?
32 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32 Base design files?
From the DominikNeugebauer/PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ESP32 Base design in my own project?
The repository has no license, so all rights stay with DominikNeugebauer. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32 Base without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in PCB
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k