Rc int arm rover
donut-hole0·rc-int-arm-rover·electrical/kicad/rc_rover_controller.kicad_sch
About the Rc int arm rover PCB
Rc int arm rover is an open source ESP32 PCB design by donut-hole0, published on GitHub. It is a board, with 9 components from 7 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. By type, the board carries 2 connectors, 2 capacitors, 1 IC, 1 battery holder and 1 switch.
It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.
From the project
group project w/ 4 highschoolers
A two-ESP32 remote-controlled rover with a 4-axis arm and gripper. A handheld controller (ESP32 + two joysticks + two potentiometers) talks to the rover (ESP32 + servos) over WiFi using UDP. The rover hosts its own WiFi access point, so no router or internet connection is needed.
- Drive and steering from the left (rover) joystick - 4-part arm: base rotation, shoulder, elbow, and gripper (no wrist) - Synchronized arm motion: one joystick axis moves the shoulder and elbow together between an upright pose and a low forward-reaching pose - Fine adjustment: two potentiometers add an offset to…
Main components on the Rc int arm rover
Rc int arm rover bill of materials (BOM)
9 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DevKitC | ESP32-DevKitC | U1 |
| 1 | JOY_ARM | J2 | |
| 1 | JOY_ROVER | J3 | |
| 1 | Battery | BT1 | |
| 2 | R_Potentiometer | RV1, RV2 | |
| 1 | SW_SPST | SW1 | |
| 2 | 100nF | C1, C2 |
Rc int arm rover design files
The KiCad project lives in the donut-hole0/rc-int-arm-rover repository on GitHub; these links point at the commit this page was built from.
Rc int arm rover: common questions
What microcontroller does the Rc int arm rover use?
The Rc int arm rover is built around the ESP32-DevKitC, from the ESP32 family.
How many components are on the Rc int arm rover?
9 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Rc int arm rover design files?
From the donut-hole0/rc-int-arm-rover repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Rc int arm rover design in my own project?
The repository has no license, so all rights stay with donut-hole0. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rc int arm rover without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k