SnakeGame
drvnprgrmr·SnakeGame·ecad/mainboard/mainboard.kicad_pcb
About the SnakeGame PCB
SnakeGame is an open source ESP32 PCB design by drvnprgrmr, published on GitHub under the MIT license. It is a 2-layer board measuring 90 × 70 mm, with 27 components from 11 distinct parts.
Its main chip is the ESP32C3 Super Mini Left, from the ESP32 family. Other key parts include the PCF8575DBR. By type, the board carries 19 resistors, 4 connectors, 2 switches, 1 IC and 1 buzzer.
From the project
Snake on a 8x8 led dot matrix.
Main components on the SnakeGame
SnakeGame bill of materials (BOM)
27 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PCF8575DBR | SSOP-24_5.3x8.2mm_P0.65mm | U1 |
| 1 | ESP32C3 Super Mini Left | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | ESP32C3 Super Mini Right | PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | Dot Matrix Side A | PinSocket_1x08_P2.54mm_Vertical | J5 |
| 1 | Dot Matrix Side B | PinSocket_1x08_P2.54mm_Vertical | J6 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Left Button | SW_Push_2P1T_Toggle_CK_PVA1xxH1xxxxxxV2 | SW1 |
| 1 | Right Button | SW_Push_2P1T_Toggle_CK_PVA1xxH1xxxxxxV2 | SW2 |
| 16 | 150 | R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7, R8 +8 |
| 1 | 10k | R_0805_2012Metric | R17 |
| 2 | 4.7k | R_0805_2012Metric | R18, R19 |
SnakeGame design files
The KiCad project lives in the drvnprgrmr/SnakeGame repository on GitHub; these links point at the commit this page was built from.
SnakeGame: common questions
What microcontroller does the SnakeGame use?
The SnakeGame is built around the ESP32C3 Super Mini Left, from the ESP32 family.
How big is the SnakeGame PCB?
The SnakeGame measures 90 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SnakeGame?
27 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the SnakeGame design files?
From the drvnprgrmr/SnakeGame repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the SnakeGame design in my own project?
Yes, under the terms of its MIT license, which drvnprgrmr chose for the repository.
Can I test firmware for the SnakeGame without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k