GameboyPi
EduCardBoden·GameboyPi·electronics/kicad-project/GameboyPi.kicad_pcb
About the GameboyPi PCB
GameboyPi is an open source PCB design by EduCardBoden, published on GitHub. It is a 2-layer board measuring 78 × 134 mm, with 45 components from 36 distinct parts.
By type, the board carries 12 resistors, 9 switches, 7 connectors, 6 test points, 6 capacitors and 2 transistors.
It belongs with the retro computing and power & battery designs in this gallery.
From the project
Backup GameboyPi
Tragbarer Retro-Handheld mit eigener Trägerplatine (KiCad 10), 3D-druckbarem Gehäuse (OpenSCAD) und LiPo-Akku. Status: Design fertig und rechnerisch geprüft, aber noch nicht gebaut. Siehe Prüfstatus und offene Risiken.
Den Ordner in VS Code öffnen, dann Strg+Shift+B („Alles bauen“). Alternativ einzeln über Terminal → Task ausführen:
- Platine bauen (KiCad): Schaltplan → Platine → Freerouting → ERC/DRC → Gerber, BOM, Pick&Place, PDFs, Renderings (~3 min) - Gehäuse bauen (OpenSCAD): Kollisionsprüfung aller Bauteile gegen die Schalen → STLs → Vorschaubilder - Nur STLs exportieren, Platine in…
GameboyPi bill of materials (BOM)
45 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | BS170 | TO-92_Inline_Wide | Q1, Q2 |
| 1 | LCD 2.4in ILI9341 SPI (MSP2401) | PinHeader_1x14_P2.54mm_Vertical | J2 |
| 1 | Adafruit PAM8302 | PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | SJ1-3525N | Jack_3.5mm_CUI_SJ1-3525N_Horizontal | J7 |
| 1 | UART Debug (GND TX RX) | PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | Adafruit PowerBoost 1000C | PinHeader_1x08_P2.54mm_Vertical | J10 |
| 1 | ADS1115 JP2 (VCC..ALERT) | PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | ADS1115 JP1 (AVDD..AGND) | PinHeader_1x06_P2.54mm_Vertical | J12 |
| 1 | PTV09A-2020F-A103 10k log | Potentiometer_Bourns_PTV09A-2_Single_Horizontal | RV1 |
| 1 | UP | SW_PUSH_6mm | SW1 |
| 1 | DOWN | SW_PUSH_6mm | SW2 |
| 1 | LEFT | SW_PUSH_6mm | SW3 |
| 1 | RIGHT | SW_PUSH_6mm | SW4 |
| 1 | A | SW_PUSH_6mm | SW5 |
| 1 | B | SW_PUSH_6mm | SW6 |
| 1 | SELECT | SW_PUSH_6mm | SW7 |
| 1 | START | SW_PUSH_6mm | SW8 |
| 1 | POWER | SW_Slide_SPDT_Angled_CK_OS102011MA1Q | SW9 |
| 1 | VBAT | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP1 |
| 1 | +5V | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP2 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | +3V3 | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP3 |
| 1 | GND | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP4 |
| 1 | PB_EN | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP5 |
| 1 | AMP_IN | TestPoint_THTPad_D1.5mm_Drill0.7mm | TP6 |
| 1 | LED rot 3mm | LED_D3.0mm | D1 |
| 1 | BAT85 | D_DO-35_SOD27_P7.62mm_Horizontal | D2 |
| 1 | 470uF 10V 10YXJ470M6.3X11 | CP_Radial_D6.3mm_P2.50mm | C1 |
| 2 | 33NF 33nF | C_Disc_D3.0mm_W1.6mm_P2.50mm | C2, C4 |
| 2 | 100uF 10V ECE-A1AKS101 | CP_Radial_D6.3mm_P2.50mm | C3, C5 |
| 1 | 100NF 100nF | C_Disc_D3.0mm_W1.6mm_P2.50mm | C6 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 2 | 270 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4 |
| 2 | 150 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R5 |
| 2 | 47K 47k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6, R7 |
| 1 | 1M | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R8 |
| 4 | 100K 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R10, R11, R12 |
GameboyPi design files
The KiCad project lives in the EduCardBoden/GameboyPi repository on GitHub; these links point at the commit this page was built from.
GameboyPi: common questions
How big is the GameboyPi PCB?
The GameboyPi measures 78 × 134 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the GameboyPi?
45 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the GameboyPi design files?
From the EduCardBoden/GameboyPi repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the GameboyPi design in my own project?
The repository has no license, so all rights stay with EduCardBoden. Use it as a reference, and ask the author before reusing the design.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1k