Buom c3-eco
ekt0810·buom-c3-eco·outputs/buom_c3_eco/hardware/buom_c3.kicad_pcb
About the Buom c3-eco PCB
Buom c3-eco is an open source ESP32 PCB design by ekt0810, published on GitHub. It is a 2-layer board measuring 60 × 40 mm, with 30 components from 22 distinct parts.
Its main chip is the XIAO ESP32-C3, from the ESP32 family. Other key parts include the 74AHCT2G125DP. By type, the board carries 12 resistors, 7 connectors, 5 capacitors, 3 transistors, 2 ICs and 1 diode.
From the project
ESP32-C3 flapping butterfly prototype: BOM, KiCad, firmware, MATLAB model and 3D viewer
- Kích thước 60 x 40 mm; 2 lớp; FR4 0,8 mm; 1 oz; mạ lỗ xuyên; bề mặt HASL không chì hoặc ENIG. - XIAO hàn castellated trên 14 pad biên. Các pad BAT/debug phía đáy được bỏ có chủ ý. USB quay ra mép ngắn theo silkscreen. - Module buck gắn ngoài qua J2. J2 không phải footprint trực tiếp của Mini-360 hoặc Pololu. - ECO không lắp J3/J4/J7/Q3/R7/R8, không lắp IMU, RP1 hoặc LED. Giữ tất cả mạch nguồn, PWM và đo pin. - J1/J2/J5/J6 có thể hàn dây trực tiếp thay header để nhẹ. Dây phải có chống kéo và kiểm tra cực. Không lấy dòng servo qua chân 5V của XIAO. - Pad vuông là pin 1. Servo: 1=GND…
Main components on the Buom c3-eco
Buom c3-eco bill of materials (BOM)
30 components, 22 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32-C3 | MCU_Seeed_C3_top14 | U1 |
| 1 | 74AHCT2G125DP | TSSOP-8_3x3mm_P0.65mm | U2 |
| 1 | AO4407A | SOIC-8_3.9x4.9mm_P1.27mm | Q1 |
| 1 | 2N7002 | SOT-23 | Q2 |
| 1 | AO3400A | SOT-23 | Q3 |
| 1 | 2S BAT 6.6-8.4V | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | BUCK external | PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | IMU 4438 | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | RP1 TX OUT | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | LEFT SERVO | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | RIGHT SERVO | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | LED WING BUS | PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | SS14 | D_SMA | D1 |
| 2 | 100n 16V | C_0805_2012Metric | C1, C3 |
| 2 | 10u 16V | C_0805_2012Metric | C2, C4 |
| 1 | 220u 16V low ESR | CP_Radial_D6.3mm_P2.50mm | C5 |
| 1 | 100k 1% | R_0805_2012Metric | R1 |
| 1 | 33k 1% | R_0805_2012Metric | R2 |
| 5 | 100k | R_0805_2012Metric | R3, R6, R8, R11, R12 |
| 1 | 10k | R_0805_2012Metric | R4 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 100R | R_0805_2012Metric | R5, R7 |
| 2 | 220R | R_0805_2012Metric | R9, R10 |
Buom c3-eco design files
The KiCad project lives in the ekt0810/buom-c3-eco repository on GitHub; these links point at the commit this page was built from.
Buom c3-eco: common questions
What microcontroller does the Buom c3-eco use?
The Buom c3-eco is built around the XIAO ESP32-C3, from the ESP32 family.
How big is the Buom c3-eco PCB?
The Buom c3-eco measures 60 × 40 mm, has 2 copper layers and is 0.8 mm thick.
How many components are on the Buom c3-eco?
30 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Buom c3-eco design files?
From the ekt0810/buom-c3-eco repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Buom c3-eco design in my own project?
The repository has no license, so all rights stay with ekt0810. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Buom c3-eco without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k