Atsaml10-breakout

elevendroids·atsaml10-breakout

Atsaml10-breakout layout, top view — open source Microchip SAM board by elevendroids

About the Atsaml10-breakout

Atsaml10-breakout is an open source Microchip SAM PCB design by elevendroids, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 24 × 50 mm, with 39 components from 22 distinct parts.

Its main chip is the ATSAML10E16A-A, from the Microchip SAM family. By type, the board carries 16 resistors, 11 capacitors, 3 connectors, 2 crystals, 2 diodes and 2 inductors.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

ATSAML1x Breakout Board

Small breakout board designed for the ATSAML10 and ATSAML11 ARM Cortex-M23 MCUs from Microchip

- minimal subset of components, no power regulation etc. - optional external main and real-time crystals - if not used, their GPIO pins can be connected to the user header by soldering relevant 0R resistors (see schematic) - two buffered user LEDs, connected to the header - no reserved GPIOs - reset button - standard 0.05" pitch SWD programming header, SWD signals also present on the pin headers

Atsaml10-breakout, from the project README
From the project README

Main components on the Atsaml10-breakout

ATSAML10E16A-A

Atsaml10-breakout bill of materials (BOM)

39 components, 22 distinct parts.

QtyPartRefs
1
ATSAML10E16A-A
U1
1
BC847BDW1
Q1
1
ABS07
32.768kHz
Abracon
Y1
1
ECS-80-10-30B-CWN-TR
8MHz
ECS
Y2
1
Left
J1
1
Right
J2
1
20021121-00010C4LF
SWD
Amphenol
J3
1
Reset
SW1
1
LED0
D1
1
LED1
D2
1
BLM18AG221SN1D
220R/100MHz
Murata
FB1
1
LPS3015-103MRB
10uH
Coilcraft
L1
2
12p
C1, C2
2
15p
C3, C4
2
10u
C5, C6
4
100n
C7, C9, C10, C11
1
1u
C8
8
0R
R1, R2, R3, R4, R5, R6, R9, R10
3
330R
R7, R11, R16
1
10k
R8
Show 2 more
QtyPartRefs
2
47k
R12, R13
2
100k
R14, R15

Atsaml10-breakout design files

The KiCad project lives in the elevendroids/atsaml10-breakout repository on GitHub; these links point at the commit this page was built from.

Atsaml10-breakout: common questions

What microcontroller does the Atsaml10-breakout use?

The Atsaml10-breakout is built around the ATSAML10E16A-A, from the Microchip SAM family.

How big is the Atsaml10-breakout?

The Atsaml10-breakout measures 24 × 50 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Atsaml10-breakout?

39 components, from 22 distinct parts. The full bill of materials is listed on this page.

Where can I download the Atsaml10-breakout design files?

From the elevendroids/atsaml10-breakout repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Atsaml10-breakout design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which elevendroids chose for the repository.

Can I test firmware for the Atsaml10-breakout without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

Similar boards