FPVSoundLogger V2
emileletueur·FPVSoundLogger_HW·pcb/FPVSoundLogger_V2.kicad_pcb
About the FPVSoundLogger V2 PCB
FPVSoundLogger V2 is an open source ESP32 PCB design by emileletueur, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board measuring 38.5 × 38.5 mm, with 34 components from 23 distinct parts.
Its main chip is the ESP32-S3-MINI-1U, from the ESP32 family. By type, the board carries 12 resistors, 9 capacitors, 8 diodes, 3 connectors and 1 IC.
From the project
FPVSoundLogger Hardware
This the Hardware part of FPVSoundLogger
- EDA Software: KiCad 9.x - Type: PCB (number of layers, dimensions) - Status: In progress / Prototype / Validated
- ⚙️🔓 Hardware: CERN-OHL-S-2.0 - 💻🔁 Software: GPL-3.0-only - 📘✍️ Documentation: CC-BY-4.0
- ✅ Feature 1 - ✅ Feature 2 - ✅ Interface X / Power supply Y
- PCB: 2 / 4 layers - Thickness: 1.6 mm - Copper: 1 oz - Finish: HASL / ENIG - Critical tolerances: yes / no
Main components on the FPVSoundLogger V2
FPVSoundLogger V2 bill of materials (BOM)
34 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-MINI-1U | ESP32-S3-MINI-1U | U1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Conn_01x04 | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J2 |
| 1 | Conn_01x06 | PinHeader_1x06_P1.00mm_Vertical | J3 |
| 1 | XTSD08G | LGA-8_8x6mm_P1.27mm | XTSD08G |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D6 |
| 2 | B5819 | D_SOD-323_HandSoldering | D10, D80 |
| 3 | ~ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D11, D12, D13 |
| 1 | 1N4148W | D_SOD-123 | D40 |
| 1 | Red Hubei KENTO Elec | D_0603 | D60 |
| 1 | 10uF/16V/X7R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 100nF/16V/X7R | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C11 |
| 1 | 1uF/16V/X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C20 |
| 1 | 10uF/16V/X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C21 |
| 5 | 100nF/10V/X7R | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C30, C40, C50, C90, C91 |
| 2 | 5.1kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R11 |
| 1 | 100kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R30 |
| 1 | 4.7kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R40 |
| 1 | 0R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R41 |
| 1 | 10kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R50 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | ~ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R51, R52, R53, R54 |
| 1 | 1kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R60 |
| 1 | 10 kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R90 |
FPVSoundLogger V2 design files
The KiCad project lives in the emileletueur/FPVSoundLogger_HW repository on GitHub; these links point at the commit this page was built from.
FPVSoundLogger V2: common questions
What microcontroller does the FPVSoundLogger V2 use?
The FPVSoundLogger V2 is built around the ESP32-S3-MINI-1U, from the ESP32 family.
How big is the FPVSoundLogger V2 PCB?
The FPVSoundLogger V2 measures 38.5 × 38.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FPVSoundLogger V2?
34 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the FPVSoundLogger V2 design files?
From the emileletueur/FPVSoundLogger_HW repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the FPVSoundLogger V2 design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which emileletueur chose for the repository.
Can I test firmware for the FPVSoundLogger V2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k