Makeshift flipper
ErdemWilkinson·makeshift-flipper·hardware/makeshift_flipper.net
About the Makeshift flipper PCB
Makeshift flipper is an open source ESP32 PCB design by ErdemWilkinson, published on GitHub under the MIT license. It is a board, with 14 components from 13 distinct parts.
Its main chip is the ESP32-C6-DEV-KIT-NX, from the ESP32 family. Other key parts include the RC522, RDM6300, VS1838B, ST7789-1.8in-240x240 and LevelShifter-1ch. By type, the board carries 6 ICs, 4 resistors, 1 transistor, 1 connector, 1 buzzer and 1 diode.
It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.
From the project
DIY Flipper Zero-style handheld on a single ESP32-C6 (ESP-IDF/C): Wi-Fi and BLE scanning tools, OLED menu UI, RFID/IR drivers in progress
Bu klasör, firmware'deki pin haritasından türetilmiş PCB üretim girdilerini içerir. Amaç: kablolamayı bir dosyaya döküp, sonunda lehimli bir PCB ürettirmek (JLCPCB / PCBWay gibi bir servise).
Güncel mimari: 118×46 mm tek perfboard (46×18 delik), kutu yok, okuma yüzü açık. RDM6300 bobini + kartı ve RC522 aşağı bakar; üstünde karton / LiPo / karton sandviçi, elektrik bandıyla sarılı. Plaka ile sandviç arası 2.5 mm hava boşluğu (perfboard artığından köprü ayaklar), vida yok. Ana README'de özet ve görseller: ../README.md.
Main components on the Makeshift flipper
Makeshift flipper bill of materials (BOM)
14 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C6-DEV-KIT-NX | ESP32-C6-DEV-KIT-NX | U1 |
| 1 | RC522 | RC522-8pin-header | U2 |
| 1 | RDM6300 | RDM6300 | U3 |
| 1 | VS1838B | Vishay_MINICAST-3pin | U4 |
| 1 | ST7789-1.8in-240x240 | LCD-ST7789-8pin | U5 |
| 1 | LevelShifter-1ch | BSS138-level-shifter | U6 |
| 1 | IR-LED-driver (NPN e.g. 2N2222 + 1k base) | TO-92_Inline | Q1 |
| 1 | LiPo-JST-PH2 | JST_PH_B2B-PH-K | J1 |
| 1 | ActiveBuzzer | Buzzer_D12.0mm_H9.5mm | BZ1 |
| 1 | IR-LED-940nm | LED_D5.0mm | D1 |
| 2 | 10k | R_Axial_DIN0207 | R1, R2 |
| 1 | 100R | R_Axial_DIN0207 | R3 |
| 1 | 1k | R_Axial_DIN0207 | R4 |
Makeshift flipper design files
The KiCad project lives in the ErdemWilkinson/makeshift-flipper repository on GitHub; these links point at the commit this page was built from.
Makeshift flipper: common questions
What microcontroller does the Makeshift flipper use?
The Makeshift flipper is built around the ESP32-C6-DEV-KIT-NX, from the ESP32 family.
How many components are on the Makeshift flipper?
14 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Makeshift flipper design files?
From the ErdemWilkinson/makeshift-flipper repository on GitHub, which has a netlist; the links under Design files point to each one.
Can I use the Makeshift flipper design in my own project?
Yes, under the terms of its MIT license, which ErdemWilkinson chose for the repository.
Can I test firmware for the Makeshift flipper without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k