Desk controller
esatilla·desk-controller·hardware/perfboard-5x10/desk_perfboard.kicad_pcb
About the Desk controller PCB
Desk controller is an open source ESP32 PCB design by esatilla, published on GitHub under the MIT license. It is a 2-layer board measuring 50 × 100 mm, with 18 components from 10 distinct parts.
Its main chip is the ESP32 CABLE, from the ESP32 family. Other key parts include the PC817. By type, the board carries 7 resistors, 5 connectors, 2 ICs, 2 diodes and 2 capacitors.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
Sit-stand desk controller: ESP32-S3 touch AMOLED, BTS7960, phone web page, HomeKit, OTA updates and hardware docs
A hand-wired logic board that sits between the ESP32 display board, the IBT-2 motor driver and the desk's encoder cable. It carries the three motor-control pull-downs, the two PC817 encoder channels, the encoder protection diodes and the button inputs. It is the soldered version of the circuit on the breadboard; the full schematic is in ../kicad and the system-level wiring in ../assembly.md.

Main components on the Desk controller
Desk controller bill of materials (BOM)
18 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | PC817 | DIP-4_W7.62mm | U4, U5 |
| 1 | ESP32 CABLE | PinHeader_1x10_P2.54mm_Vertical | J10 |
| 1 | IBT-2 LOGIC | PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | ENCODER | PinHeader_1x04_P2.54mm_Vertical | J12 |
| 1 | 5V INPUT | PinHeader_1x02_P2.54mm_Vertical | J13 |
| 1 | BUTTON CABLE | PinHeader_1x03_P2.54mm_Vertical | J14 |
| 2 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2 |
| 2 | 100nF | Capacitor_P5.08 | C4, C5 |
| 5 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R6, R7 |
| 2 | 1.5k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R5 |
Desk controller design files
The KiCad project lives in the esatilla/desk-controller repository on GitHub; these links point at the commit this page was built from.
Desk controller: common questions
What microcontroller does the Desk controller use?
The Desk controller is built around the ESP32 CABLE, from the ESP32 family.
How big is the Desk controller PCB?
The Desk controller measures 50 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Desk controller?
18 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Desk controller design files?
From the esatilla/desk-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Desk controller design in my own project?
Yes, under the terms of its MIT license, which esatilla chose for the repository.
Can I test firmware for the Desk controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k