WALL-E
F9Motion·WALL-E·KiCad/WALL-E.kicad_pcb
About the WALL-E PCB
WALL-E is an open source ESP32 PCB design by F9Motion, published on GitHub. It is a 2-layer board measuring 80 × 80 mm, with 30 components from 7 distinct parts.
Its main chip is the ESP32-S2-WROVER, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 23 modules, 2 ICs, 2 resistors, 1 connector, 1 battery holder and 1 switch.
It belongs with the robotics & motion and iot & wireless designs in this gallery.
From the project
robot from popular pixart cartoon
Main components on the WALL-E
WALL-E bill of materials (BOM)
30 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-S2-WROVER | ESP32-S2-WROVER | U2 |
| 23 | Motor_DC | TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | M1, M2, M3, M4, M5, M6, M7, M8 +15 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_Amphenol_124019772112A | J1 |
| 1 | Battery_Cell | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | BT1 |
| 1 | SW_Push | SW_XKB_DM1-16UC-1 | SW1 |
| 2 | 5.1k | R_0805_2012Metric | R1, R2 |
WALL-E design files
The KiCad project lives in the F9Motion/WALL-E repository on GitHub; these links point at the commit this page was built from.
- LayoutKiCad/WALL-E.kicad_pcb
- SchematicKiCad/WALL-E.kicad_sch
WALL-E: common questions
What microcontroller does the WALL-E use?
The WALL-E is built around the ESP32-S2-WROVER, from the ESP32 family.
How big is the WALL-E PCB?
The WALL-E measures 80 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the WALL-E?
30 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the WALL-E design files?
From the F9Motion/WALL-E repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the WALL-E design in my own project?
The repository has no license, so all rights stay with F9Motion. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the WALL-E without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k