13 open source boards using the ESP32-S2-WROVER
Real designs built with the ESP32-S2-WROVER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ESP32-S2-Breakout
eggsampler
61 × 30.5 mm37 parts2LMIT126ESP32
BastWiFi
ElectronicCats
60 × 22.9 mm29 parts2LNo license3ESP32
Motorcycle telemetry unit
Data-ptr
133.8 × 95.4 mm109 parts2LUnlicense1ESP32
Flipper Zero Wifi Module
aaakum4
80 × 40 mm56 parts4LGPL-3.01ESP32
PintApple
camielverdult
40 × 40 mm36 parts2LNo license1ESP32
WALL-E
F9Motion
80 × 80 mm30 parts2LNo license0ESP32
RoboCloud
miameows
77 × 50.1 mm20 parts2LMIT0- schematic only · 44 partsESP32
Fandom
tfindlay-au
44 partsNo license0 - schematic only · 10 partsESP32
Blood-Oxygen and-Heart-Rate-Monitoring-System
Zabauski
10 partsNo license0 - schematic only · 9 partsESP32
Modular navigator
Bhaveshcoding
9 partsMIT0 ESP32
On AIR controller board
ViktorStiskala
64 × 52 mm38 parts2LNo license0ESP32
Practice
wlatif-cmyk
77.5 × 106 mm7 parts2LNo license8ESP32
Mess-ESP32
unicab369
89.7 × 98.8 mm126 parts2LNo license0
How designs wire the ESP32-S2-WROVER
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the ESP32-S2-WROVER connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a capacitor to GND on 8 of 10 designs, most often 100 nF (then 1 µF).
- The EN pin has a pull-up to 3.3V on 6 of 10 designs, most often 10 kΩ (then 45 kΩ).
- The IO46 pin is left unconnected on 7 of 10 designs (a signal on 3).
- The 3V3 pin is tied to 3.3V on 6 of 10 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 26, 42, 43 | Connected to: GND 80% · a signal 20% | — |
| 3V3pin 2 | Connected to: 3.3V 60% · a signal 40% | — |
| IO00pin 3 | Connected to: A connector 30% · not connected 20% |
|
| IO18pin 21 | Connected to: A connector 20% · not connected 30% |
|
| USB_D-pin 22 | Connected to: A connector 60% · not connected 30% |
|
| USB_D+pin 23 | Connected to: A connector 60% · not connected 30% |
|
| IO21pin 24 | Connected to: Not connected 60% · a signal 40% | — |
| IO26pin 25 | Connected to: Not connected 60% · a signal 40% | — |
| IO33pin 27 | Connected to: Not connected 60% · a signal 40% | — |
| IO38pin 32 | Connected to: Not connected 60% · a signal 40% | — |
| IO39pin 33 | Connected to: Not connected 60% · a signal 40% | — |
| IO40pin 34 | Connected to: Not connected 60% · a signal 40% | — |
| IO41pin 35 | Connected to: Not connected 60% · a signal 40% | — |
| IO45pin 39 | Connected to: Not connected 60% · a signal 40% | — |
| IO46pin 40 | Connected to: Not connected 70% · a signal 30% | — |
| ENpin 41 | Connected to: A connector 40% |
|
24 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESP32-S2-Breakout by eggsampler, Practiceschematic by wlatif-cmyk, BastWiFi by ElectronicCats and Flipper Zero Wifi Module by aaakum4.
The ESP32-S2-WROVER in open source designs
The gallery holds 13 open source boards using the ESP32-S2-WROVER from 13 GitHub repositories; a typical one measures about 77.2 × 51 mm and carries around 36 components.
90% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is ESP32-S2-Breakout by eggsampler.
Microcontrollers on boards using the ESP32-S2-WROVER
What boards using the ESP32-S2-WROVER are built for
ESP32-S2-WROVER: common questions
Where can I find a ESP32-S2-WROVER reference design?
Each of the 13 boards on this page is a real design using the ESP32-S2-WROVER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32-S2-WROVER EN pin connected?
The EN pin has a capacitor to GND on 8 of 10 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 10 open source designs using the ESP32-S2-WROVER.
How is the ESP32-S2-WROVER IO46 pin connected?
The IO46 pin is left unconnected on 7 of 10 designs (a signal on 3). Counted from the KiCad layouts of 10 open source designs using the ESP32-S2-WROVER.
How is the ESP32-S2-WROVER 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 6 of 10 designs (a signal on 4). Counted from the KiCad layouts of 10 open source designs using the ESP32-S2-WROVER.
Which microcontrollers do boards using the ESP32-S2-WROVER use?
Most are built on ESP32 (13).
How big is a typical board using the ESP32-S2-WROVER?
The median is 77.2 × 51 mm, and 90% are two-layer designs.
What is the most popular open source board using the ESP32-S2-WROVER?
By GitHub stars, ESP32-S2-Breakout by eggsampler, with 126 stars.
Can I simulate one of these boards using the ESP32-S2-WROVER before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.