HardLabs

Tiny 2nmosfet

fademike·fly_drone·kicad/tiny_2nmosfet/tiny_2nmosfet.kicad_pcb

Tiny 2nmosfet PCB layout, top view — open source AVR/Arduino board by fademike

About the Tiny 2nmosfet PCB

Tiny 2nmosfet is an open source AVR/Arduino PCB design by fademike, published on GitHub. It is a 2-layer board measuring 24.8 × 17.1 mm, with 36 components from 7 distinct parts.

Its main chip is the ATtiny13A-SS, from the AVR/Arduino family. By type, the board carries 14 resistors, 11 test points, 5 diodes, 2 ICs, 2 transistors and 2 capacitors.

It belongs with the robotics & motion, rf & radio and sensors designs in this gallery.

From the project

scheme, pcb, code for drone

How to connect: Android phone (AppFlyControl) usb-uart(example: cp2102) uart->rf (STM8S003ANDSI4463) flydrone or: Android phone (QGroundControl or AppFlyControl) Linux PC (flyLinuxServer) uart->rf (STM8S003ANDSI4463) flydrone

on board: - DC-DC for 2,3,..S battery operation. To operate on a 1S battery, it is necessary to replace the components to turn off the DC-DC. - RF SI4463 433MHz radio transceiver. when changing the frequency, you can to change components and programmatically set a different frequency. - imu mpu6050 - 4pcs 3-pin connector for servo motor/ESC (IMP 1-2 ms) for 4pcs brushed…

Tiny 2nmosfet, from the project README
From the project README

Main components on the Tiny 2nmosfet

ATtiny13A-SS

Tiny 2nmosfet bill of materials (BOM)

36 components, 7 distinct parts.

QtyPartRefs
2
ATtiny13A-SS
U1, U2
2
FDS6890A
Q1, Q2
11
TestPoint
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +3
5
1N5819WS
D2, D3, D4, D5, D6
2
1u
C1, C2
8
0
R1, R2, R3, R4, R5, R6, R7, R8
6
10k
R9, R10, R11, R12, R13, R14

Tiny 2nmosfet design files

The KiCad project lives in the fademike/fly_drone repository on GitHub; these links point at the commit this page was built from.

Tiny 2nmosfet: common questions

What microcontroller does the Tiny 2nmosfet use?

The Tiny 2nmosfet is built around the ATtiny13A-SS, from the AVR/Arduino family.

How big is the Tiny 2nmosfet PCB?

The Tiny 2nmosfet measures 24.8 × 17.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Tiny 2nmosfet?

36 components, from 7 distinct parts. The full bill of materials is listed on this page.

Where can I download the Tiny 2nmosfet design files?

From the fademike/fly_drone repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Tiny 2nmosfet design in my own project?

The repository has no license, so all rights stay with fademike. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Tiny 2nmosfet without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in fly_drone

Similar boards