8 open source boards using the ATtiny13A-SS
Real designs built with the ATtiny13A-SS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Mora blinker
kissadamfkut
33 × 30 mm15 parts2LMIT34AVR/Arduino
Keyboard
dragonlock2
200 × 100 mm225 parts2LApache-2.013AVR/Arduino
TX5823
ep092
54.5 × 47.6 mm94 parts2LNo license9AVR/Arduino
Auto dimmer
ilyushkin
51 × 70 mm46 parts2LGPL-3.02AVR/Arduino
UG56-attiny13a pwm controller
universalgeek56
25 × 31.5 mm21 parts2LMIT1AVR/Arduino
Servo tester
ironiron
39.6 × 23.9 mm10 parts2LUnlicense0AVR/Arduino
Tiny 2nmosfet
fademike
24.8 × 17.1 mm36 parts2LNo license1AVR/Arduino
Slider
lucanastasio
44 × 39 mm35 parts2LNo license1
How designs wire the ATtiny13A-SS
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ATtiny13A-SS connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF).
- The PB3 pin has a series resistor on 4 of 8 designs, most often 120 Ω (then 10 Ω).
- The PB0 pin has a series resistor on 4 of 8 designs, most often 120 Ω (then 330 kΩ).
- The PB1 pin has a series resistor on 4 of 8 designs, most often 120 Ω (then 300 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PB3pin 2 | Connected to: Signal 63% · not connected 25% |
|
| PB4pin 3 | Connected to: Signal 100% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| PB0pin 5 | Connected to: A connector 50% |
|
| PB1pin 6 | Connected to: A connector 50% |
|
| PB2pin 7 | Connected to: A connector 50% |
|
| VCCpin 8 | Connected to: 5V 75% · a signal 25% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mora blinker by kissadamfkut, Keyboard by dragonlock2, TX5823 by ep092 and Auto dimmer by ilyushkin.
The ATtiny13A-SS in open source designs
The gallery holds 8 open source boards using the ATtiny13A-SS from 8 GitHub repositories; a typical one measures about 41.8 × 35.3 mm and carries around 36 components.
100% are two-layer designs, the rest use four layers or more, and 63% carry an open source license.
The most starred is Mora blinker by kissadamfkut.
Parts used alongside the ATtiny13A-SS
Microcontrollers on boards using the ATtiny13A-SS
What boards using the ATtiny13A-SS are built for
ATtiny13A-SS: common questions
Where can I find a ATtiny13A-SS reference design?
Each of the 8 boards on this page is a real design using the ATtiny13A-SS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATtiny13A-SS VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the ATtiny13A-SS.
What resistor goes on the ATtiny13A-SS PB3 pin?
The PB3 pin has a series resistor on 4 of 8 designs, most often 120 Ω (then 10 Ω). Counted from the KiCad layouts of 8 open source designs using the ATtiny13A-SS.
What resistor goes on the ATtiny13A-SS PB0 pin?
The PB0 pin has a series resistor on 4 of 8 designs, most often 120 Ω (then 330 kΩ). Counted from the KiCad layouts of 8 open source designs using the ATtiny13A-SS.
Which microcontrollers do boards using the ATtiny13A-SS use?
Most are built on AVR/Arduino (8).
How big is a typical board using the ATtiny13A-SS?
The median is 41.8 × 35.3 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATtiny13A-SS?
By GitHub stars, Mora blinker by kissadamfkut, with 34 stars.
Can I simulate one of these boards using the ATtiny13A-SS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.