Aerix-20x20

FBIopeningUPP·aerix-20x20·hardware/fc-v1/fc-v1.kicad_pcb

Aerix-20x20 PCB layout, top view — open source Raspberry Pi board by FBIopeningUPP

About the Aerix-20x20 PCB

Aerix-20x20 is an open source Raspberry Pi PCB design by FBIopeningUPP, published on GitHub. It is a 4-layer board measuring 31 × 31 mm, with 88 components from 42 distinct parts.

Its main chip is the RP2354A, from the Raspberry Pi family. Other key parts include the DPS368XTSA1, ICM-40609-D, W25Q128JVPIQ, C477821 and C2861882. By type, the board carries 41 capacitors, 21 resistors, 9 LEDs, 7 ICs, 4 diodes and 2 inductors.

From the project

i wanted to design my own flight controller for fpv racing, so i made aerix. it fits a 20×20 mm stack and runs on an rp2354a with an icm-40609-d gyro.

i wanted to design my own flight controller for fpv racing, so i made aerix. it fits a 20×20 mm stack and runs on an rp2354a with an icm-40609-d gyro.

i went with solder pads for the esc, receiver and vtx to keep the board small. the 8 rgb leds around the corners are there because they look cool af.

- kicad project - gerbers and drill files - interactive BOM (download and open in a browser)

Aerix-20x20, from the project README
From the project README

Main components on the Aerix-20x20

Aerix-20x20 bill of materials (BOM)

88 components, 42 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RP2354A
U1
1
DPS368XTSA1
Infineon(英飞凌)
U2
1
ICM-40609-D
U3
1
W25Q128JVPIQ
W25Q128JVPIQTR
Winbond(华邦)
U4
1
C477821
MP9943GQ-Z
U5
1
C2861882
TLV75533PDQNR
U6
1
C80670
LP5907MFX-3.3/NOPB
U7
1
C282405
2N7002BK,215
Q1
1
ABM10-167-12.000MHZ-T3
ABRACON
X1
1
USB4105-GF-A
J1
1
Momentary Tactile Button - Biege
SW1
1
LTST-C191KRKT
LED1
8
WS2812B-2020-V6
worldsemi
LED10, LED11, LED12, LED13, LED14, LED15, LED16, LED17
2
PMEG4010CEH,115
D1, D2
1
BAT54WS
D4
1
C94934
TPD2EUSB30ADRTR
D5
1
AOTA-B201610S3R3-101-T
3.3uH
ABRACON
L1
1
NRS4018T100MDGJ
10uH_1.0A_4018
Taiyo Yuden
L3
3
4.7uF
C1, C11, C12
11
0.1uF
C2, C3, C4, C5, C6, C7, C8, C9 +3
Show 22 more
QtyPartRefs
2
10pF
C15, C16
1
2.2uF
C17
6
100nF
C18, C20, C21, C22, C23, C24
1
10nF
C19
2
10uF 50V X7R
C25, C26
1
1uF 50V
C27
2
22uF 10V X7R
C28, C29
4
2.2uF 10V
C30, C31, C32, C33
8
100nF 16V X7R
C42, C43, C44, C45, C46, C47, C48, C49
1
33
R1
2
1k
R2, R3
2
4.7k
R4, R5
1
1M
R6
1
52.3k 1%
R7
1
10k 1%
R8
1
20R
R9
1
100R
R19
1
100k
R20
2
5.1k 1%
R21, R22
2
27R
R23, R24
5
10k
R25, R28, R29, R30, R31
1
330R
R32

Aerix-20x20 design files

The KiCad project lives in the FBIopeningUPP/aerix-20x20 repository on GitHub; these links point at the commit this page was built from.

Aerix-20x20: common questions

What microcontroller does the Aerix-20x20 use?

The Aerix-20x20 is built around the RP2354A, from the Raspberry Pi family.

How big is the Aerix-20x20 PCB?

The Aerix-20x20 measures 31 × 31 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the Aerix-20x20?

88 components, from 42 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Aerix-20x20 design files?

From the FBIopeningUPP/aerix-20x20 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Aerix-20x20 design in my own project?

The repository has no license, so all rights stay with FBIopeningUPP. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Aerix-20x20 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards