Esp c3-addressable leds
About the Esp c3-addressable leds PCB
Esp c3-addressable leds is an open source ESP32 PCB design by flaviut, published on GitHub. It is a 2-layer board measuring 60 × 50 mm, with 7 components from 6 distinct parts.
Its main chip is the Waveshare-ESP32-C3-Zero, from the ESP32 family. Other key parts include the 74AHCT1G125. By type, the board carries 3 capacitors, 2 ICs, 1 connector and 1 resistor.
From the project
Waveshare ESP32-C3-Zero based addressable LED driver
Main components on the Esp c3-addressable leds
Esp c3-addressable leds bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | Waveshare-ESP32-C3-Zero | U1 |
| 1 | 74AHCT1G125 | SOT-23-5_HandSoldering | U2 |
| 1 | Conn_01x03 | SolderWire-0.5sqmm_1x03_P4.8mm_D0.9mm_OD2.3mm_Relief | J1 |
| 2 | 1uF | C_0603_1608Metric | C1, C2 |
| 1 | 1mF | CP_Radial_D8.0mm_P2.50mm | C3 |
| 1 | 220 | R_0603_1608Metric | R1 |
Esp c3-addressable leds design files
The KiCad project lives in the flaviut/hardware repository on GitHub; these links point at the commit this page was built from.
Esp c3-addressable leds: common questions
What microcontroller does the Esp c3-addressable leds use?
The Esp c3-addressable leds is built around the Waveshare-ESP32-C3-Zero, from the ESP32 family.
How big is the Esp c3-addressable leds PCB?
The Esp c3-addressable leds measures 60 × 50 mm, has 2 copper layers and is 1.600198 mm thick.
How many components are on the Esp c3-addressable leds?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp c3-addressable leds design files?
From the flaviut/hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp c3-addressable leds design in my own project?
The repository has no license, so all rights stay with flaviut. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp c3-addressable leds without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in hardware
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k