HardLabs

Driver 32mm atmega v0p2

floesche·LED-Display_G4_Hardware_Driver·driver_32mm_atmega_v0p2/driver_32mm_atmega_v0p2.kicad_pcb

Driver 32mm atmega v0p2 PCB layout, top view — open source AVR/Arduino board by floesche

About the Driver 32mm atmega v0p2 PCB

Driver 32mm atmega v0p2 is an open source AVR/Arduino PCB design by floesche, published on GitHub under the CC-BY-4.0 license. It is a board measuring 32 × 32 mm, with 17 components from 9 distinct parts.

Its main chip is the ATMEGA328P-MUR, from the AVR/Arduino family. Other key parts include the DMC2400UV-7DI. By type, the board carries 9 resistors, 2 ICs, 2 connectors, 2 capacitors, 1 crystal and 1 LED.

It belongs with the displays & leds designs in this gallery, and the repository also holds 1 earlier revision of it.

Main components on the Driver 32mm atmega v0p2

ATMEGA328P-MURDMC2400UV-7DI

Driver 32mm atmega v0p2 bill of materials (BOM)

17 components, 9 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATMEGA328P-MUR
ATMEGA168-A
Digikey
IC1
1
DMC2400UV-7DI
ULN2804A
Digikey
U1
1
490-1199-6
CR
Digikey
X1
2
952-2119
CONN_8
Digikey
P1, P2
1
LED_8X8
MATRIX1
2
1276-1258-1
0.1uF
Digikey
C1, C2
4
311-4.7KGR
82
Digikey
R1, R2, R3, R4
4
RG16P160B
82
Digikey
R5, R6, R7, R8
1
RG16P160B
10K
Digikey
R9

Driver 32mm atmega v0p2 design files

The KiCad project lives in the floesche/LED-Display_G4_Hardware_Driver repository on GitHub; these links point at the commit this page was built from.

Driver 32mm atmega v0p2: common questions

What microcontroller does the Driver 32mm atmega v0p2 use?

The Driver 32mm atmega v0p2 is built around the ATMEGA328P-MUR, from the AVR/Arduino family.

How big is the Driver 32mm atmega v0p2 PCB?

The Driver 32mm atmega v0p2 measures 32 × 32 mm and is 1.6002 mm thick.

How many components are on the Driver 32mm atmega v0p2?

17 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Driver 32mm atmega v0p2 design files?

From the floesche/LED-Display_G4_Hardware_Driver repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Driver 32mm atmega v0p2 design in my own project?

Yes, under the terms of its CC-BY-4.0 license, which floesche chose for the repository.

Can I test firmware for the Driver 32mm atmega v0p2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in LED-Display_G4_Hardware_Driver

Earlier revisions in the repo: driver_32mm_atmega_v0p1

Similar boards