Co design of electronic products
gabrieldelmonte·Co-design_of_electronic_products·Hardware/Projeto_2022014552/Projeto_2022014552.kicad_pcb
About the Co design of electronic products PCB
Co design of electronic products is an open source STM32 PCB design by gabrieldelmonte, published on GitHub under the MIT license. It is a 2-layer board measuring 70 × 70 mm, with 61 components from 31 distinct parts.
Its main chip is the STM32F030K6T6TR, from the STM32 family. Other key parts include the LD1117S33TR, 24LC512 and MCP2200-I-SO. By type, the board carries 17 capacitors, 16 resistors, 8 connectors, 6 diodes, 4 ICs and 4 switches.
It belongs with the displays & leds designs in this gallery.
From the project
Design files and documentation for PBLE01 - Electronic Product Co-design, a university project developed at UNIFEI
2. Operation Subcircuit - STM32F030K6 microcontroller - 8MHz crystal oscillator - Boot mode selection
3. Peripheral Subcircuit - USB-Serial interface (MCP2200) - EEPROM memory (24LC512) - Ambient light sensor (PDV-P8103)
4. Expansion Interfaces - SPI (4-wire + power) - I²C (2-wire + power) - GPIO breakout
Main components on the Co design of electronic products
Co design of electronic products bill of materials (BOM)
61 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F030K6T6TR | QFP80P900X900X160-32N | U1 |
| 1 | LD1117S33TR | SOT230P700X180-4N | U2 |
| 1 | 24LC512 | SOIC127P794X203-8N | U3 |
| 1 | MCP2200-I-SO | SOIC20 | U4 |
| 1 | ATS08A | XTAL_HC49P488W43L1085T450H368 | Y1 |
| 1 | ATS12A | ATS12A | Y2 |
| 1 | USB4215-03-A_REVA | GCT_USB4215-03-A_REVA | J1 |
| 1 | Conector SWD | PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | Conector_SelectBootMode | PinSocket_1x02_P2.54mm_Vertical | J3 |
| 1 | Conector_BOOT0 | PinSocket_1x01_P2.54mm_Vertical | J4 |
| 1 | Conector - LCD | PinSocket_1x16_P2.54mm_Vertical | J5 |
| 1 | Conector de expansão - I2C | PinSocket_1x05_P2.54mm_Vertical | J6 |
| 1 | Conector de expansão - SPI | PinSocket_1x07_P2.54mm_Vertical | J7 |
| 1 | Conector de expansão geral | PinSocket_1x04_P2.54mm_Vertical | J8 |
| 1 | 0ZCH0050FF2G | RESC3225X75N | F1 |
| 2 | 5.1 kR | R_0805_2012Metric | RCC1, RCC2 |
| 1 | 3296W–1–103RLF | TRIM_3296W-1-103RLF | RV1 |
| 4 | 1825910-6 | SW_1825910-6-4 | SW1, SW2, SW3, SW-Reset1 |
| 6 | SM0805UOC | SM0805UOC | D1, D2, D3, D4, D5, D6 |
| 2 | 10 uF | C_0805_2012Metric | C1, C14 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | 22 pF | C_0805_2012Metric | C2, C4, C15, C16, C17 |
| 1 | 1 uF | C_0805_2012Metric | C3 |
| 7 | 100 nF | C_0805_2012Metric | C5, C6, C7, C8, C9, C10, C11 |
| 2 | 4.7 uF | C_0805_2012Metric | C12, C13 |
| 3 | 10 kR | R_0805_2012Metric | R1, R3, R5 |
| 3 | 150 R | R_0805_2012Metric | R2, R9, R12 |
| 3 | 62 R | R_0805_2012Metric | R4, R10, R13 |
| 4 | 1 kR | R_0805_2012Metric | R6, R7, R8, R15 |
| 1 | 4.7 kR | R_0805_2012Metric | R11 |
| 1 | PDV-P8103 | PHODET_PDV-P8103 | R14 |
| 1 | 47 R | R_0805_2012Metric | R16 |
Co design of electronic products design files
The KiCad project lives in the gabrieldelmonte/Co-design_of_electronic_products repository on GitHub; these links point at the commit this page was built from.
Co design of electronic products: common questions
What microcontroller does the Co design of electronic products use?
The Co design of electronic products is built around the STM32F030K6T6TR, from the STM32 family.
How big is the Co design of electronic products PCB?
The Co design of electronic products measures 70 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Co design of electronic products?
61 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the Co design of electronic products design files?
From the gabrieldelmonte/Co-design_of_electronic_products repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Co design of electronic products design in my own project?
Yes, under the terms of its MIT license, which gabrieldelmonte chose for the repository.
Can I test firmware for the Co design of electronic products without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k