16 open source boards using the 24LC512
Real designs built with the 24LC512, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Vna mm synth
loxodes
314.5 × 201 mm428 parts6LNo license205L-Star
jacgoudsmit
99.7 × 80 mm51 parts2LMIT57AVR/Arduino
Gpstracker
blemasle
79.3 × 59.2 mm65 parts2LMIT33ESP8266
Deck65
and3rson
254 × 80 mm183 parts2LGPL-3.015AVR/Arduino
Myfirstmacropad
eeble
139.7 × 69.9 mm61 parts2LCC-BY-SA-4.05TI MSP430/CC
Projet Sound Bar DIY
HodearS
165.7 × 85 mm799 parts4LNo license2STM32
USB-TO-EtherCAT-Adapter-Board
Sudeshpandit
61 × 53 mm80 parts2LNo license1STM32
694200101R2
BEKOS-Keyboards
438.6 × 125.8 mm397 parts2LCC-BY-SA-4.00STM32
Factory in a box
klaus-liebler
188 × 65 mm264 parts4LNo license0Microchip SAM
Samd51 gps alarm clock
KrHaaland
80 × 50 mm149 parts2LNo license0STM32
Test Projekt
Siegmundshof93
86.2 × 91.9 mm147 parts2LNo license0NXP
PBLE01 CO DESIGN DE PRODUTOS ELETRONICOS
LucasToledo16
79 × 75.8 mm75 parts2LNo license0Lpc11u14-board bringup
alighieribot
80 × 80 mm64 parts2LMIT0STM32
Co design of electronic products
gabrieldelmonte
70 × 70 mm61 parts2LMIT0STM32
Project tarkus
blfp1
94 × 48 mm46 parts2LNo license0JC2 - IO2 Board
Emile666
233.7 × 160 mm96 parts2LNo license3
How designs wire the 24LC512
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the 24LC512 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 1 kΩ).
- The SCL pin has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 1 kΩ).
- The A2 pin is tied to GND on 14 of 16 designs (a signal on 2).
- The A0 pin is tied to GND on 13 of 16 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 81% · a signal 19% | — |
| A1pin 2 | Connected to: GND 81% | — |
| A2pin 3 | Connected to: GND 88% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: The microcontroller 56%, a connector 50% |
|
| SCLpin 6 | Connected to: The microcontroller 56%, a connector 50% |
|
| WPpin 7 | Connected to: GND 69% · a signal 31% | — |
| VCCpin 8 | Connected to: 3.3V 94% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vna mm synth by loxodes, L-Star by jacgoudsmit, Gpstracker by blemasle and Deck65 by and3rson.
The 24LC512 in open source designs
The gallery holds 16 open source boards using the 24LC512 from 16 GitHub repositories; a typical one measures about 96.8 × 77.9 mm and carries around 88 components.
81% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Vna mm synth by loxodes.
Parts used alongside the 24LC512
Microcontrollers on boards using the 24LC512
What boards using the 24LC512 are built for
24LC512: common questions
Where can I find a 24LC512 reference design?
Each of the 16 boards on this page is a real design using the 24LC512. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the 24LC512 SDA pin?
The SDA pin has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 16 open source designs using the 24LC512.
What pull-up resistor is used on the 24LC512 SCL pin?
The SCL pin has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 16 open source designs using the 24LC512.
How is the 24LC512 A2 pin connected?
The A2 pin is tied to GND on 14 of 16 designs (a signal on 2). Counted from the KiCad layouts of 16 open source designs using the 24LC512.
What parts are used alongside the 24LC512?
The AMS1117-3.3, LD1117S33TR, FT232RL, LD1117DT50TR and MCP2200-I-SO appear in the most repositories here.
Which microcontrollers do boards using the 24LC512 use?
Most are built on STM32 (6), AVR/Arduino (2), ESP8266 (1) and NXP (1).
How big is a typical board using the 24LC512?
The median is 96.8 × 77.9 mm, and 81% are two-layer designs.
What is the most popular open source board using the 24LC512?
By GitHub stars, Vna mm synth by loxodes, with 205 stars.
Can I simulate one of these boards using the 24LC512 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.