Cric-Pro-Hardware
gaurav3611·Cric-Pro-Hardware·pcb/sswingg-bat.kicad_pcb
About the Cric-Pro-Hardware PCB
Cric-Pro-Hardware is an open source ESP32 PCB design by gaurav3611, published on GitHub. It is a 2-layer board measuring 48.3 × 60 mm, with 10 components from 9 distinct parts.
Its main chip is the ESP32-C3 Super Mini, from the ESP32 family. Other key parts include the GY-BMI160 and TP4056 module. By type, the board carries 3 ICs, 2 capacitors, 2 resistors, 1 connector, 1 switch and 1 diode.
It belongs with the power & battery, sensors and iot & wireless designs in this gallery.
From the project
Bat sensor for SwingLab (CricPro): ESP32-C3 Super Mini, BMI160, LiPo and TP4056. Circuit diagrams, staged Arduino sketches and a build guide.
A small sensor that sits on a cricket bat and sends every movement of the bat to the SSwinGG dashboard over Bluetooth. This folder holds the circuit, the firmware, and a guide that builds it one stage at a time, so that each stage is tested before the next part is added.
It is written for someone who has not done this before. Each stage says what to wire, what to upload, what you should see, and what is going on between the parts.

Main components on the Cric-Pro-Hardware
Cric-Pro-Hardware bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 Super Mini | ESP32-C3_SuperMini_Socket | U1 |
| 1 | GY-BMI160 | GY-BMI160_Socket | U2 |
| 1 | TP4056 module | TP4056_Module_Wired | U3 |
| 1 | Battery | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | SS12D00G3 | SW_Slide_SS12D00G3 | SW1 |
| 1 | 1N5817 | D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 100NF 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 220uF 10V | CP_Radial_D6.3mm_P2.50mm | C2 |
| 2 | 100k 1% | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
Cric-Pro-Hardware design files
The KiCad project lives in the gaurav3611/Cric-Pro-Hardware repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/sswingg-bat.kicad_pcb
- Schematicpcb/sswingg-bat.kicad_sch
- BOMpcb/bom.csv
Cric-Pro-Hardware: common questions
What microcontroller does the Cric-Pro-Hardware use?
The Cric-Pro-Hardware is built around the ESP32-C3 Super Mini, from the ESP32 family.
How big is the Cric-Pro-Hardware PCB?
The Cric-Pro-Hardware measures 48.3 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cric-Pro-Hardware?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cric-Pro-Hardware design files?
From the gaurav3611/Cric-Pro-Hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Cric-Pro-Hardware design in my own project?
The repository has no license, so all rights stay with gaurav3611. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Cric-Pro-Hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k