LcdFlip
About the LcdFlip PCB
LcdFlip is an open source PCB design by ghent360, published on GitHub under the Custom license license. It is a 2-layer board measuring 45.5 × 18 mm, with 4 components from 3 distinct parts.
It belongs with the robotics & motion designs in this gallery.
From the project
32-bit 3D Printer controller board using STM32F407 and replaceable TMC2660/2209 stepper drivers.
PrntrBoard V2 ====================== PrntrBoard V2 is the next iteration of my 3D printer controller design. The V1 was very good, except it had one major drawback - the stepper drivers were soldered on the board which would make the design expensive. This V2 design has 6 replaceable motor drivers. While traditional RAMPS based boards use pin headers to house the driver boards, I'm using PCIe 1x slots. This design has several advantages: + the driver PCB layout can be more flexible as there are fewer constraints on the driver board dimensions + drivers are placed vertically on the board which…
LcdFlip bill of materials (BOM)
4 components, 3 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | IDC 2x5 | IDC-Header_2x05_P2.54mm_Vertical | J1 |
| 2 | HDR 2x5 | PinSocket_2x05_P2.54mm_Vertical | J2, J4 |
| 1 | C183609 IDC 2x5 | IDC-Header_2x05_P2.54mm_Vertical | J3 |
LcdFlip design files
The KiCad project lives in the ghent360/PrntrBoardV2 repository on GitHub; these links point at the commit this page was built from.
LcdFlip: common questions
How big is the LcdFlip PCB?
The LcdFlip measures 45.5 × 18 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LcdFlip?
4 components, from 3 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LcdFlip design files?
From the ghent360/PrntrBoardV2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LcdFlip design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
More boards in PrntrBoardV2
STM32PrntrBoardV2
148.7 × 104.3 mm272 parts2LCustom license45
STM32T12 Control
49.5 × 38.2 mm45 parts4LCustom license45
ESP8266WiFi-Addon
44 × 26 mm28 parts2LCustom license45
STM32TMC2130 Driver
36.7 × 39.4 mm24 parts2LCustom license45
STM32TMC2660 Driver
36.7 × 39.4 mm23 parts4LCustom license45
STM32TMC2209 Driver
36.7 × 39.4 mm22 parts2LCustom license45
STM32DRV-StepStick
36.7 × 39.4 mm14 parts2LCustom license45
MP-Power
17 × 15.7 mm12 parts2LCustom license45
XL-Power
27 × 22 mm6 parts2LCustom license45
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7k
Cube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1k
Mesabob
rene-dev
87.5 × 50 mm44 parts2LGPL-3.0979
Bob
100 × 100 mm140 parts2LGPL-3.0979
Triple adapter
57 × 75 mm26 parts2LGPL-3.0979
Trollerv2
100 × 75 mm33 parts4LGPL-3.0979