HoG
GoTouchGra55·HoG·Kicad/HoG.kicad_pcb
About the HoG PCB
HoG is an open source STM32 PCB design by GoTouchGra55, published on GitHub under the MIT license. It is a 6-layer board measuring 60 × 60 mm, with 92 components from 45 distinct parts.
Its main chip is the STM32H743VITX, from the STM32 family. Other key parts include the ICM-45686, BMP581 and TPS54302. By type, the board carries 37 capacitors, 23 resistors, 18 connectors, 6 ICs, 3 inductors and 2 switches.
It belongs with the robotics & motion, rf & radio and sensors designs in this gallery.
From the project
Hand of God is a humanitarian aid drone.

Main components on the HoG
HoG bill of materials (BOM)
92 components, 45 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H743VITX STM32H743VITx | LQFP-100_14x14mm_P0.5mm | U1 |
| 2 | ICM-45686 | IC_ICM-45686 | U2, U3 |
| 1 | BMP581 | BMP581 | U4 |
| 2 | TPS54302 | SOT-23-6 | U5, U6 |
| 1 | 25MHZ 25MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | DEBUG | JST_EH_S5B-EH_1x05_P2.50mm_Horizontal | J1 |
| 1 | TYPE-C_16PIN_2MD__073_ | SHOUHAN_TYPE-C_16PIN_2MD__073_ | J2 |
| 1 | GPS | JST_EH_S6B-EH_1x06_P2.50mm_Horizontal | J3 |
| 1 | TEL | JST_EH_S5B-EH_1x05_P2.50mm_Horizontal | J4 |
| 1 | ESC[1-3] | SolderWire-0.5sqmm_1x03_P4.6mm_D0.9mm_OD2.1mm | J5 |
| 1 | ESC[4-6] | SolderWire-0.5sqmm_1x03_P4.6mm_D0.9mm_OD2.1mm | J6 |
| 1 | POWER | AMASS_XT60-M_1x02_P7.20mm_Vertical | J7 |
| 1 | ESC_1 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J8 |
| 1 | ESC_2 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J9 |
| 1 | ESC_3 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J10 |
| 1 | ESC_4 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J11 |
| 1 | ESC_5 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J12 |
| 1 | ESC_6 | SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mm | J13 |
| 1 | Servos | SolderWire-0.5sqmm_1x03_P4.6mm_D0.9mm_OD2.1mm | J14 |
| 1 | Power | PinHeader_1x02_P2.54mm_Horizontal | J15 |
Show 25 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | +5V Pads | PinHeader_1x03_P2.54mm_Vertical | J16 |
| 1 | MICRO_SD_CARD_DET1 Micro_SD_Card_Det1 | microSD_HC_Hirose_DM3AT-SF-PEJM5 | J17 |
| 1 | AUX | PinHeader_1x02_P2.54mm_Horizontal | J18 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW1 |
| 1 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 2 | D_Schottky | D_SOD-123 | D1, D2 |
| 1 | FerriteBead | C_0603_1608Metric | FB1 |
| 1 | 10UH 10uH | L_Cenker_CKCS3012 | L1 |
| 1 | 6.8UH 6.8uH | L_Cenker_CKCS4030 | L2 |
| 23 | 100NF 100nF | C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C12, C13 +15 |
| 6 | 10UF 10uF | C_0603_1608Metric | C7, C10, C11, C22, C27, C38 |
| 2 | 18PF 18pF | C_0402_1005Metric | C8, C9 |
| 2 | 1UF 1uF | C_0603_1608Metric | C14, C34 |
| 1 | 33UF 33uF | C_0603_1608Metric | C24 |
| 1 | 75PF 75pF | C_0402_1005Metric | C25 |
| 1 | 56PF 56pF | C_0402_1005Metric | C29 |
| 1 | 44UF 44uF | C_0603_1608Metric | C30 |
| 10 | 10K | R_0402_1005Metric | R1, R15, R16, R17, R18, R19, R20, R21 +2 |
| 2 | 5.1K | R_0402_1005Metric | R2, R3 |
| 2 | 400K | R_0603_1608Metric | R4, R10 |
| 2 | 30K | R_0603_1608Metric | R5, R12 |
| 3 | 100K | R_0603_1608Metric | R6, R11, R14 |
| 2 | 49.9R | R_0402_1005Metric | R7, R9 |
| 1 | 13.3K | R_0402_1005Metric | R8 |
| 1 | 22.1K | R_0603_1608Metric | R13 |
HoG design files
The KiCad project lives in the GoTouchGra55/HoG repository on GitHub; these links point at the commit this page was built from.
- LayoutKicad/HoG.kicad_pcb
- SchematicKicad/HoG.kicad_sch
- BOMKicad/production/bom.csv
HoG: common questions
What microcontroller does the HoG use?
The HoG is built around the STM32H743VITX, from the STM32 family.
How big is the HoG PCB?
The HoG measures 60 × 60 mm, has 6 copper layers and is 1.6 mm thick.
How many components are on the HoG?
92 components, from 45 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the HoG design files?
From the GoTouchGra55/HoG repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the HoG design in my own project?
Yes, under the terms of its MIT license, which GoTouchGra55 chose for the repository.
Can I test firmware for the HoG without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k