51 open source boards using the BMP581
Real designs built with the BMP581, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Watch-DevKit-HW
ZSWatch
100 × 70 mm100 parts4LGPL-3.0187Raspberry Pi
Inki l2
c0de111
47.2 × 55.5 mm60 parts2LApache-2.039ESP32
ESPHome-Indoor-Multi-Sensor
mikelawrence
52.5 × 59.7 mm97 parts4LCERN-OHL-P-2.012ESP32
Lowpower epaper thermometer
antoinecellerier
48 × 35 mm75 parts2LGPL-3.08Nordic nRF
OpenBikeComputer
timohueser
37 × 61 mm10 parts2LGPL-3.08Watch-HW
ZSWatch
41 × 37.5 mm62 parts4LGPL-3.05Spinali mcxn t1 hub
CogniPilot
36.5 × 46 mm203 parts6LApache-2.02STM32
IRIS
teletype7
50 × 100 mm160 parts4LMIT2STM32
UltraHawk
InSynchronous
50 × 87 mm76 parts2LMIT2RP2040/RP2350
StratosCore
pantojinho
60 × 84 mm245 parts4LNo license1RP2040/RP2350
Sol-Mk.-I
HIIACODER
78.2 × 46.8 mm72 parts4LMIT1ESP32
CanSat
budabalint
54 × 52 mm439 parts4LNo license0ESP32
Tinker mantis
Tinkerbug-Robotics
22.4 × 75 mm264 parts8LGPL-3.00STM32
Fc h743
dvntekim
50 × 50 mm178 parts6LNo license0STM32
CANSAT-M2-2026
Engineer162
55 × 100 mm156 parts4LCERN-OHL-S-2.00STM32
Weather station poc
CruvixDev
165 × 91.2 mm141 parts4LNo license0RP2040/RP2350
FligthComputers
ManuelRao
50 × 72.5 mm131 parts4LNo license0STM32
CC M7
OzanE1
40 × 65 mm126 parts4LLGPL-2.10STM32
CC M7
OzanE1
40 × 65 mm123 parts4LLGPL-2.10STM32
CANSAT ARLISS STM32
JosephPalacios-so
90 × 75 mm110 parts4LNo license0STM32
HoG
GoTouchGra55
60 × 60 mm92 parts6LMIT0STM32
Pangotag PCB LCSC compat2
andrewo3
31.9 × 27.2 mm91 parts6LNo license0ESP32
Tar team1-hardware
pranavs41
36 × 39 mm83 parts4LNo license0ESP32
MicroMETER
AUXSPACEeV
32 × 66 mm82 parts4LCERN-OHL-P-2.00STM32
Tulpar Mini FCB
ErdemHtyl
53.5 × 53.5 mm81 parts4LBSD-3-Clause0ESP32
Ledify
notaroomba
35.5 × 52.5 mm79 parts4LNo license0STM32
Flight controller
andreadamiano
50 × 50 mm73 parts6LNo license0ESP32
OpenCycle
Vishvak365
46 × 86.4 mm67 parts4LNo license0RP2040/RP2350
Peregrine
Gibson431
65 × 35 mm65 parts4LNo license0ESP32
Flysys test
nejcokorn
90 × 45 mm64 parts2LNo license0STM32
HermesFC
Daksh-Saksena
51.4 × 51.4 mm64 parts4LMIT0STM32
Weather pill
freder202
42.9 × 16 mm63 parts4LNo license0ESP32
Esp
akseliahonpera
86 × 75 mm61 parts2LNo license0STM32
Stm32logger
Birb-jpg
30 × 30 mm59 parts2LNo license0ESP32
Notahawk
bimmui
115.9 × 61.5 mm50 parts2LNo license0Microchip SAM
Rotor sensor
c4deszes
37 × 32.5 mm46 parts2LNo license0
How designs wire the BMP581
Read from the KiCad layouts of 37 open source designs, one per repository: what each pin of the BMP581 connects to, and the resistors, capacitors and other passives placed on it.
- The VDDIO pin has a decoupling capacitor on 34 of 37 designs, most often 100 nF (then 10 µF).
- The VDD pin has a decoupling capacitor on 34 of 37 designs, most often 100 nF (then 10 µF).
- The SCK pin has a pull-up to 3.3V on 24 of 37 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SDI pin has a pull-up to 3.3V on 24 of 37 designs, most often 4.7 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDIOpin 1 | Connected to: 3.3V 89% |
|
| SCKpin 2 | Connected to: The microcontroller 62% |
|
| VSSpin 3, 8, 9 | Connected to: GND 99% | — |
| SDIpin 4 | Connected to: The microcontroller 62% |
|
| CSBpin 6 | Connected to: 3.3V 62% · a signal 27% | — |
| VDDpin 10 | Connected to: 3.3V 86% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Watch-DevKit-HW by ZSWatch, Inki by c0de111, ESPHome-Indoor-Multi-Sensor by mikelawrence and Lowpower epaper thermometer by antoinecellerier.
The BMP581 in open source designs
The gallery holds 51 open source boards using the BMP581 from 39 GitHub repositories; a typical one measures about 49 × 55.5 mm and carries around 79 components.
72% use four copper layers or more, and 41% carry an open source license.
The most starred is Watch-DevKit-HW by ZSWatch.
Parts used alongside the BMP581
Microcontrollers on boards using the BMP581
What boards using the BMP581 are built for
BMP581: common questions
Where can I find a BMP581 reference design?
Each of the 51 boards on this page is a real design using the BMP581. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the BMP581 VDDIO pin?
The VDDIO pin has a decoupling capacitor on 34 of 37 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 37 open source designs using the BMP581.
What decoupling capacitors do designs use on the BMP581 VDD pin?
The VDD pin has a decoupling capacitor on 34 of 37 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 37 open source designs using the BMP581.
What pull-up resistor is used on the BMP581 SCK pin?
The SCK pin has a pull-up to 3.3V on 24 of 37 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 37 open source designs using the BMP581.
What parts are used alongside the BMP581?
The USBLC6-2SC6, BMI270, MMC5983MA, USBLC6-2P6 and BMI088 appear in the most repositories here.
Which microcontrollers do boards using the BMP581 use?
Most are built on STM32 (21), ESP32 (17), RP2040/RP2350 (4) and Raspberry Pi (2).
How big is a typical board using the BMP581?
The median is 49 × 55.5 mm, and 28% are two-layer designs.
What is the most popular open source board using the BMP581?
By GitHub stars, Watch-DevKit-HW by ZSWatch, with 187 stars.
Can I simulate one of these boards using the BMP581 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.