Atmo monitor
gpgreen·atmo-monitor
About the Atmo monitor PCB
Atmo monitor is an open source STM32 PCB design by gpgreen, published on GitHub under the MIT license. It is a 2-layer board measuring 60 × 66 mm, with 21 components from 12 distinct parts.
Its main chip is the STM32F103CBT6, from the STM32 family. Other key parts include the LP2950-3.3_TO252 and Power. By type, the board carries 7 capacitors, 5 resistors, 3 ICs, 3 connectors, 2 switches and 1 transistor.
It belongs with the sensors, displays & leds and test & measurement designs in this gallery.
From the project
Kicad design for atmospheric measurement sensor with Display
KiCad design for a atmospheric measurement board. The MCU is a stm32f103cbt6. There are 2 main sensors. One is the PMS2007, which measures particulates, ie PM2.5. The other sensor is a BME680, which measures temperature, pressure, and organic compounds. The measurements are output on an E-Ink tri-color display.
This design is a continuation of a project that I did using a nucleo dev board and a perfboard pcb. The main goals used for this design:
Main components on the Atmo monitor
Atmo monitor bill of materials (BOM)
21 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103CBT6 | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | LP2950-3.3_TO252 | TO-252-2 | U2 |
| 1 | Power | Adafruit Powerboost 500+ | U3 |
| 1 | IRLML0100TRPbF | SOT-23 | Q1 |
| 1 | E-Ink | PinHeader_1x13_P2.54mm_Vertical | J1 |
| 1 | Qwiic | JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J3 |
| 1 | PM Sensor | JST_PH_B8B-PH-K_1x08_P2.00mm_Vertical | J4 |
| 1 | Reset | OnShine KPT-1187B | SW1 |
| 1 | 1825232-1 | TE-1825232-1 | SW2 |
| 1 | 2.2uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 6 | 1uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3, C4, C5, C6, C7 |
| 5 | 10K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R3, R4, R5 |
Atmo monitor design files
The KiCad project lives in the gpgreen/atmo-monitor repository on GitHub; these links point at the commit this page was built from.
- Layoutatmo-monitor.kicad_pcb
- Schematicatmo-monitor.kicad_sch
Atmo monitor: common questions
What microcontroller does the Atmo monitor use?
The Atmo monitor is built around the STM32F103CBT6, from the STM32 family.
How big is the Atmo monitor PCB?
The Atmo monitor measures 60 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Atmo monitor?
21 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Atmo monitor design files?
From the gpgreen/atmo-monitor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Atmo monitor design in my own project?
Yes, under the terms of its MIT license, which gpgreen chose for the repository.
Can I test firmware for the Atmo monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k