Boili
Hauke12345·Boili·hardware/pcb/spot_heater.kicad_pcb
About the Boili PCB
Boili is an open source ESP32 PCB design by Hauke12345, published on GitHub. It is a 2-layer board measuring 96.5 × 62 mm, with 28 components from 25 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 7 resistors, 5 capacitors, 4 connectors, 3 diodes, 2 ICs and 2 switches.
It belongs with the iot & wireless designs in this gallery.
From the project
Electrical and mechanical design
ESP32 board that turns a water heater's contactor on during the cheapest electricity hours. It fetches Nord Pool spot prices over WiFi and switches the contactor coil, never the heater itself. The tank's own thermostat and over-temperature limiter stay in series with the heater element.
KiCad 9 project. ERC: 0 errors / 0 warnings. DRC: 0 violations, 0 unconnected, schematic parity OK. SPICE checks (relay driver, boot, supply rails, power-up) are in simulation/.
Main components on the Boili
Boili bill of materials (BOM)
28 components, 25 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32 | U2 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | MAINS IN (L, N) | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | TO CONTACTOR COIL (L_SW, N) | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J2 |
| 1 | PROG | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | DS18B20 | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | T1A 250V (TR5) | Fuseholder_TR5_Littelfuse_No560_No460 | F1 |
| 1 | G5Q-1A 5VDC | Relay_SPST_Omron-G5Q-1A | K1 |
| 1 | HLK-PM01 (5V 0.6A) | Converter_ACDC_Hi-Link_HLK-PMxx | PS1 |
| 1 | 275VAC S07K275 | RV_Disc_D7mm_W3.4mm_P5mm | RV1 |
| 1 | RESET | SW_PUSH_6mm | SW1 |
| 1 | BOOT / BOOST | SW_PUSH_6mm | SW2 |
| 1 | SS14 | D_SMA | D1 |
| 1 | RED (heating) | LED_0805_2012Metric | D2 |
| 1 | GREEN (status) | LED_0805_2012Metric | D3 |
| 2 | 22uF 10V | C_1206_3216Metric | C1, C2 |
| 1 | 10uF | C_0805_2012Metric | C3 |
| 1 | 100nF | C_0805_2012Metric | C4 |
| 1 | 1uF | C_0805_2012Metric | C5 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10k | R_0805_2012Metric | R1, R2 |
| 1 | 100R | R_0805_2012Metric | R3 |
| 1 | 100k | R_0805_2012Metric | R4 |
| 2 | 1k | R_0805_2012Metric | R5, R6 |
| 1 | 4k7 | R_0805_2012Metric | R7 |
Boili design files
The KiCad project lives in the Hauke12345/Boili repository on GitHub; these links point at the commit this page was built from.
Boili: common questions
What microcontroller does the Boili use?
The Boili is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the Boili PCB?
The Boili measures 96.5 × 62 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Boili?
28 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Boili design files?
From the Hauke12345/Boili repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Boili design in my own project?
The repository has no license, so all rights stay with Hauke12345. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Boili without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k