HardLabs

Blind SleepyLoRa Slave

Hootie81·SleepyLoRa·Electronics/Slave/Blind_SleepyLoRa_Slave.kicad_pcb

Blind SleepyLoRa Slave PCB layout, top view — open source ESP32 board by Hootie81

About the Blind SleepyLoRa Slave PCB

Blind SleepyLoRa Slave is an open source ESP32 PCB design by Hootie81, published on GitHub under the MIT license. It is a 2-layer board measuring 130.5 × 39.5 mm, with 17 components from 8 distinct parts.

Its main chip is the ESP32SUPERMINI_ESP32-SUPERMINI, from the ESP32 family. By type, the board carries 6 resistors, 4 capacitors, 3 ICs and 3 connectors.

It belongs with the rf & radio designs in this gallery.

From the project

SleepyLoRa Binds, A LoRa based solution for low power actuation of plantation shutters

This folder contains all the electronics design files, schematics, PCB layouts, and bills of materials (BOM) for the SleepyLoRa Blinds System. The electronics are designed to be easy to assemble, cost-effective, and reliable for DIY smart blinds control.

Each device folder contains: - KiCad project files (.pro, .sch, .kicadpcb`, etc.) - Gerber files for PCB manufacturing - Device-specific BOM (bill of materials)

Main components on the Blind SleepyLoRa Slave

ESP32SUPERMINI_ESP32-SUPERMINI

Blind SleepyLoRa Slave bill of materials (BOM)

17 components, 8 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
~
U1
1
ESP32SUPERMINI_ESP32-SUPERMINI
U2
1
~
U3
1
Conn_01x04_Socket
J1
2
Conn_01x04_Socket
J3, J4
1
R_Potentiometer
RV1
4
C
C1, C2, C3, C4
6
10K
R1, R2, R3, R4, R5, R6

Blind SleepyLoRa Slave design files

The KiCad project lives in the Hootie81/SleepyLoRa repository on GitHub; these links point at the commit this page was built from.

Blind SleepyLoRa Slave: common questions

What microcontroller does the Blind SleepyLoRa Slave use?

The Blind SleepyLoRa Slave is built around the ESP32SUPERMINI_ESP32-SUPERMINI, from the ESP32 family.

How big is the Blind SleepyLoRa Slave PCB?

The Blind SleepyLoRa Slave measures 130.5 × 39.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Blind SleepyLoRa Slave?

17 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Blind SleepyLoRa Slave design files?

From the Hootie81/SleepyLoRa repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Blind SleepyLoRa Slave design in my own project?

Yes, under the terms of its MIT license, which Hootie81 chose for the repository.

Can I test firmware for the Blind SleepyLoRa Slave without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in SleepyLoRa

Similar boards