Esp32-fluorimeter
hridaKun·esp32-fluorimeter·Schematic/Circuit.kicad_sch

About the Esp32-fluorimeter PCB
Esp32-fluorimeter is an open source ESP32 PCB design by hridaKun, published on GitHub under the MIT license. It is a board, with 17 components from 16 distinct parts.
Its main chip is the ESP32 DevKit (38-pin), from the ESP32 family. Other key parts include the MCP602 and ADS1115 module. By type, the board carries 5 resistors, 3 ICs, 3 capacitors, 2 switches, 2 diodes and 1 transistor.
From the project
A low-cost, portable fluorimeter built around an ESP32. A blue LED excites the sample, a photodiode picks up the fluorescence, and the ESP32 shows the concentration on a 2.4" TFT.
A low-cost, portable fluorimeter built around an ESP32. A blue LED excites the sample, a photodiode picks up the fluorescence, and the ESP32 shows the concentration on a 2.4" TFT.
- The photodiode sits at 90° to the LED so the excitation beam doesn't hit it directly. - The TIA converts photocurrent to voltage: Vout = Vref + Iph × Rf, with Rf = 1 MΩ and Vref = 0.157 V. - Each reading switches the LED off and on 32 times and averages (LED on − LED off). This cancels room light, dark current and op-amp offset. - A blank (plain solvent) is subtracted, and a straight-line calibration from known…
Main components on the Esp32-fluorimeter
Esp32-fluorimeter bill of materials (BOM)
17 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32 DevKit (38-pin) | U1 | |
| 1 | MCP602 | DIP-8_W7.62mm | U2 |
| 1 | ADS1115 module | U3 | |
| 1 | BC547 | TO-92_Inline | Q1 |
| 1 | 2.4in TFT (ILI9341, SPI) | J1 | |
| 1 | MEASURE | SW_PUSH_6mm | SW1 |
| 1 | BLANK | SW_PUSH_6mm | SW2 |
| 1 | BPW34 | Osram_DIL2_4.3x4.65mm_P5.08mm | D1 |
| 1 | Blue LED 470nm | LED_D5.0mm | D2 |
| 1 | 10u | CP_Radial_D5.0mm_P2.00mm | C1 |
| 1 | 330p (Cf) | C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 100n | C_Disc_D5.0mm_W2.5mm_P5.00mm | C3 |
| 1 | 20k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 2 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R5 |
| 1 | 1M (Rf) | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 100 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
Esp32-fluorimeter design files
The KiCad project lives in the hridaKun/esp32-fluorimeter repository on GitHub; these links point at the commit this page was built from.
- SchematicSchematic/Circuit.kicad_sch
- BOMdocs/BOM.md
Esp32-fluorimeter: common questions
What microcontroller does the Esp32-fluorimeter use?
The Esp32-fluorimeter is built around the ESP32 DevKit (38-pin), from the ESP32 family.
How many components are on the Esp32-fluorimeter?
17 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-fluorimeter design files?
From the hridaKun/esp32-fluorimeter repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-fluorimeter design in my own project?
Yes, under the terms of its MIT license, which hridaKun chose for the repository.
Can I test firmware for the Esp32-fluorimeter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k