28 open source boards using the MCP602
Real designs built with the MCP602, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Max2-audio dac
dilshan
101.8 × 52.5 mm153 parts2LMIT60AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.049Zx sizif-512-ext
UzixLS
213 × 64 mm145 parts2LMIT19AzizLight
devttys0
70.1 × 29.2 mm55 parts2LNo license6AVR/Arduino
Mycelium
microresearch
74.5 × 83.7 mm126 parts2LGPL-3.05STM32
Sensored-3-P-BLDC-Closed-Loop-V1
g-rahul
100 × 100 mm114 parts2LNo license5AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.02STM32
Front panel
WiseLord
248.5 × 36 mm80 parts2LNo license1Bord λ principial
Alex2269
53.3 × 71 mm62 parts2LNo license1AVR/Arduino
PTDriver
wallaceowen
100 × 50 mm61 parts2LMIT1STM32
PROMETHEUS
EPFLRocketTeam
115 × 50 mm259 parts4LNo license0Artanis
aep
60 × 101 mm97 parts2LNo license0Radiation Detection Payload Power
pbbp0904
72.6 × 46.7 mm53 parts2LMIT0STM32
PIRON
shaunak153
130 × 20 mm46 parts2LNo license0- schematic only · 17 partsESP32
Esp32-fluorimeter
hridaKun
17 partsMIT0 AVR/Arduino
Mycleium pcb before thereminchange
microresearch
74.5 × 83.7 mm126 parts2LGPL-3.05STM32
OTTO-main
cester-ino
239 × 80 mm100 parts2LGPL-3.02V1Panel
pilotniq
182.5 × 65 mm58 parts2LNo license2Pwm2dc
Alex2269
20.3 × 17.8 mm22 parts2LNo license1EMGSensor
SonDinh23
16 × 28 mm40 parts4LGPL-3.00Mini project 1
mbelanger0
25.3 × 14.3 mm17 parts2LNo license0RP2040/RP2350
Carte FX 0
PhysicsDptAngers
100 × 100 mm107 parts2LMIT87Mycelium pcb radio
microresearch
74.5 × 83.7 mm62 parts2LGPL-3.05ChargeControl
pilotniq
64 × 27 mm46 parts2LNo license2Heater shunt
Alex2269
23 × 17.2 mm17 parts2LNo license1AND8bit
Tert2
100 × 100 mm61 parts2LNo license0V9938-board
Lintaroh
100 × 135 mm57 parts2LMIT0Small shunt
Alex2269
19.8 × 15.1 mm17 parts2LNo license1
How designs wire the MCP602
Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the MCP602 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 17 of 20 designs, most often 10 kΩ (then 24 kΩ).
- The V- pin is tied to GND on 16 of 20 designs (not connected on 2, 3.3V on 2).
- The + pins have a pull-up to 3.3V on 12 of 20 designs, most often 100 kΩ (then 15 kΩ).
- Pin 1 has a series resistor on 11 of 20 designs, most often 10 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 30% |
|
| -pin 2, 6 | Connected to: Signal 90% |
|
| +pin 3, 5 | Connected to: Signal 85% |
|
| V-pin 4 | Connected to: GND 80% | — |
| Pin 7 | Connected to: The microcontroller 25% · 1.65 15% |
|
| V+pin 8 | Connected to: 3.3V 70% · not connected 15% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Carte FX 0 by PhysicsDptAngers, Max2-audio dac by dilshan, OTTOtact by cester-ino and Zx sizif-512-ext by UzixLS.
The MCP602 in open source designs
The gallery holds 28 open source boards using the MCP602 from 21 GitHub repositories; a typical one measures about 100 × 64 mm and carries around 62 components.
93% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Carte FX 0 by PhysicsDptAngers.
Parts used alongside the MCP602
Microcontrollers on boards using the MCP602
What boards using the MCP602 are built for
MCP602: common questions
Where can I find a MCP602 reference design?
Each of the 28 boards on this page is a real design using the MCP602. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP602 - pin?
The - pins have a series resistor on 17 of 20 designs, most often 10 kΩ (then 24 kΩ). Counted from the KiCad layouts of 20 open source designs using the MCP602.
How is the MCP602 V- pin connected?
The V- pin is tied to GND on 16 of 20 designs (not connected on 2, 3.3V on 2). Counted from the KiCad layouts of 20 open source designs using the MCP602.
What pull-up resistor is used on the MCP602 + pin?
The + pins have a pull-up to 3.3V on 12 of 20 designs, most often 100 kΩ (then 15 kΩ). Counted from the KiCad layouts of 20 open source designs using the MCP602.
What parts are used alongside the MCP602?
The AMS1117-3.3, 74HC125, ATmega32U4-AU, FS312F-G and L7805 appear in the most repositories here.
Which microcontrollers do boards using the MCP602 use?
Most are built on AVR/Arduino (5), STM32 (5), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the MCP602?
The median is 100 × 64 mm, and 93% are two-layer designs.
What is the most popular open source board using the MCP602?
By GitHub stars, Carte FX 0 by PhysicsDptAngers, with 87 stars.
Can I simulate one of these boards using the MCP602 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.