LCD-button box
Icyconfusion·LCD-button-box·PCB/lcd button box.kicad_pcb
About the LCD-button box PCB
LCD-button box is an open source ESP32 PCB design by Icyconfusion, published on GitHub. It is a 2-layer board measuring 153.3 × 81.4 mm, with 29 components from 5 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. By type, the board carries 24 switches, 4 connectors and 1 IC.
It belongs with the displays & leds and iot & wireless designs in this gallery.
From the project
A DIY stream deck style button box using a 3.5" LCD.
The button box uses an LCD seated at the bottom of the case. Above that, a PCB is suspended, containing the necessary tact switches. The PCB has square cutout holes to show the LCD image through. To press the buttons, there is a 3d printed stand on each set of 4 switches (one button), holding a clear acrylic square. Through this mechanism, the LCD is visible, and pressing the acylic presses the tact switches, registering a keypress. The bottom right button functions as a change layer button, where pressing that will cycle the button box to a new 'layer', with different icons and key outputs.
LCD-button box bill of materials (BOM)
29 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32_30pin | U1 |
| 2 | Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J1, J2 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 24 | SW_Push | SW_PUSH_6mm | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +16 |
LCD-button box design files
The KiCad project lives in the Icyconfusion/LCD-button-box repository on GitHub; these links point at the commit this page was built from.
LCD-button box: common questions
What microcontroller does the LCD-button box use?
The LCD-button box is built around the ESP32_30pin, from the ESP32 family.
How big is the LCD-button box PCB?
The LCD-button box measures 153.3 × 81.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LCD-button box?
29 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LCD-button box design files?
From the Icyconfusion/LCD-button-box repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LCD-button box design in my own project?
The repository has no license, so all rights stay with Icyconfusion. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the LCD-button box without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k