Ornament
About the Ornament PCB
Ornament is an open source ESP8266 PCB design by idlehandsdev, published on GitHub. It is a 2-layer board measuring 76.2 × 93.4 mm, with 27 components from 17 distinct parts.
Its main chip is the ESP-12E, from the ESP8266 family. By type, the board carries 6 LEDs, 6 resistors, 3 connectors, 3 jumpers, 3 switches and 3 capacitors.
It belongs with the robotics & motion designs in this gallery.
From the project
The best way to spread Christmas cheer is to upload it to the internet!
Main components on the Ornament
Ornament bill of materials (BOM)
27 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-12E | ESP-12E_NoTH | U2 |
| 1 | CONN_01X02 | Buzzer_12x9.5RM7.6 | P1 |
| 1 | EXT_REG | pololu_power_3.3v-5v | P2 |
| 1 | CONN_01X06 | Connectors_JST_SM06B-SRSS-TB | P3 |
| 1 | Batt_N | AAA_SingleHolder | BT1 |
| 1 | Jumper_NC_Small | SOLDER-JUMPER_1-WAY-CLOSED | JP1 |
| 1 | Jumper_NO_Small | SOLDER-JUMPER_1-WAY | JP2 |
| 1 | Jumper_NC_Small | SOLDER-JUMPER_1-WAY | JP4 |
| 1 | B | SW_SPST_FSMSM | SW1 |
| 1 | GPIO0 | SW_SPST_FSMSM | SW2 |
| 1 | RESET | SW_SPST_FSMSM | SW3 |
| 6 | WS2812B | WS2812B | LED1, LED2, LED3, LED4, LED5, LED6 |
| 1 | D | SOD-323 | D2 |
| 2 | 100uF | c_elec_6.3x5.3 | C1, C2 |
| 1 | 1uF | C_0402_Hand | C3 |
| 3 | 10K | R_0402_Hand | R1, R2, R5 |
| 3 | 1K | R_0402_Hand | R3, R4, R6 |
Ornament design files
The KiCad project lives in the idlehandsdev/esp_ornaments repository on GitHub; these links point at the commit this page was built from.
Ornament: common questions
What microcontroller does the Ornament use?
The Ornament is built around the ESP-12E, from the ESP8266 family.
How big is the Ornament PCB?
The Ornament measures 76.2 × 93.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ornament?
27 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ornament design files?
From the idlehandsdev/esp_ornaments repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Ornament design in my own project?
The repository has no license, so all rights stay with idlehandsdev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ornament without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in esp_ornaments
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738
ESP8266Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506
ESP8266RatGDO-OpenSource-Bare-ESP8266
55 × 82.7 mm20 parts2LMIT506
ESP8266RatGDO-OpenSource-D1Mini-ESP8266
47.8 × 63.3 mm12 parts2LMIT506
ESP8266Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398