Cpld
ifilot·slot-otter·pcb/cpld/cpld.kicad_pcb
About the Cpld PCB
Cpld is an open source PCB design by ifilot, published on GitHub. It is a 2-layer board measuring 104.4 × 82.7 mm, with 29 components from 20 distinct parts.
Other key parts include the CY62128ELL-45SXI, 74HC00 and 74HC74. By type, the board carries 7 capacitors, 7 resistors, 6 test points, 4 ICs, 3 connectors and 1 crystal.
From the project
8-bit ISA card to interface with a FAT32 formatted SD card
An 8-bit ISA card for accessing FAT16- or FAT32-formatted SD cards under MS-DOS.
Slot-otter lets a DOS PC use an SD card as an ordinary drive. Fill the card with files on a modern computer, insert it into your vintage PC, and copy or run them from DOS. A working setup has three parts:
- the Slot-otter card in a free 8-bit ISA slot; - the OTTERSD driver on the PC's hard drive, loaded at startup; - an SD card with a FAT16 or FAT32 file system.

Main components on the Cpld
Cpld bill of materials (BOM)
29 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CY62128ELL-45SXI ATF1504AS-xJx44 | PLCC-44_THT-Socket | U1 |
| 1 | 74HC00 AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | 74HC74 74LVC125 | TSSOP-14_4.4x5mm_P0.65mm | U3 |
| 1 | 74HC00 74HCT688 | SOIC-20W_7.5x12.8mm_P1.27mm | U4 |
| 1 | 16MHz | Oscillator_DIP-14 | X1 |
| 1 | MICRO_SD_CARD_DET1 Micro_SD_Card_Det1 | CONN9_MSD-1_CUD | J1 |
| 1 | Bus_ISA_8bit_AB_Rev0 | ISA_CARD_EDGE_CONNECTOR_8BIT_Rev1 | J2 |
| 1 | Atmel-JTAG-10 | IDC-Header_2x05_P2.54mm_Vertical | J3 |
| 1 | ADDR SEL | SW_DIP_SPSTx08_Slide_9.78x22.5mm_W7.62mm_P2.54mm | SW1 |
| 1 | ~{CS} | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP1 |
| 1 | CLK | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP2 |
| 1 | MOSI | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP3 |
| 1 | MISO | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP4 |
| 2 | GND | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP5, TP6 |
| 6 | 0.1UF 0.1uF | C_0805_2012Metric | C1, C2, C3, C4, C5, C7 |
| 1 | 0.1UF 100uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C6 |
| 1 | 560 10k | R_0805_2012Metric | R1 |
| 2 | 3.3k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R5 |
| 2 | 10K 3.3k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 2 | 10k | R_Array_Convex_4x0612 | RN1, RN2 |
Cpld design files
The KiCad project lives in the ifilot/slot-otter repository on GitHub; these links point at the commit this page was built from.
Cpld: common questions
How big is the Cpld PCB?
The Cpld measures 104.4 × 82.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cpld?
29 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cpld design files?
From the ifilot/slot-otter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Cpld design in my own project?
The repository has no license, so all rights stay with ifilot. Use it as a reference, and ask the author before reusing the design.