Prototype
ifilot·slot-otter·pcb/prototype/prototype.kicad_pcb
About the Prototype PCB
Prototype is an open source PCB design by ifilot, published on GitHub. It is a 2-layer board measuring 151.6 × 82.7 mm, with 45 components from 33 distinct parts.
Other key parts include the CY62128ELL-45SXI, 74HC00, 74HC74, 74HC163 and 74HC138. By type, the board carries 14 capacitors, 13 ICs, 6 test points, 5 resistors, 3 diodes and 2 connectors.
From the project
8-bit ISA card to interface with a FAT32 formatted SD card
An 8-bit ISA card for accessing FAT16- or FAT32-formatted SD cards under MS-DOS.
Slot-otter lets a DOS PC use an SD card as an ordinary drive. Fill the card with files on a modern computer, insert it into your vintage PC, and copy or run them from DOS. A working setup has three parts:
- the Slot-otter card in a free 8-bit ISA slot; - the OTTERSD driver on the PC's hard drive, loaded at startup; - an SD card with a FAT16 or FAT32 file system.

Main components on the Prototype
Prototype bill of materials (BOM)
45 components, 33 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CY62128ELL-45SXI 74HC00 | DIP-14_W7.62mm_Socket | U1 |
| 1 | 74HC00 74HCT32 | DIP-14_W7.62mm_Socket | U2 |
| 1 | 74HC74 74HCT139 | DIP-16_W7.62mm_Socket | U3 |
| 1 | 74HC00 74HC163 | DIP-16_W7.62mm_Socket | U4 |
| 1 | 74HC163 74HC00 | DIP-14_W7.62mm_Socket | U5 |
| 1 | 74HC138 74HC165 | DIP-16_W7.62mm_Socket | U6 |
| 1 | 74HC123 74HC595 | DIP-16_W7.62mm_Socket | U7 |
| 1 | 74HC273 74HCT688 | DIP-20_W7.62mm_Socket | U8 |
| 1 | 74HC32 74HCT245 | DIP-20_W7.62mm_Socket | U9 |
| 1 | 74HC32 74HC74 | DIP-14_W7.62mm_Socket | U10 |
| 1 | 74HC273 74HC08 | DIP-14_W7.62mm_Socket | U11 |
| 1 | 74HC165 74HC04 | DIP-14_W7.62mm_Socket | U12 |
| 1 | 74HC595 74HC74 | DIP-14_W7.62mm_Socket | U13 |
| 1 | 16MHz | Oscillator_DIP-14 | X1 |
| 1 | MICRO_SD_CARD_DET1 SDCARD | sdcard-socket | J1 |
| 1 | Bus_ISA_8bit_AB_Rev0 | ISA_CARD_EDGE_CONNECTOR_8BIT_Rev1 | J2 |
| 1 | ADDR SEL | SW_DIP_SPSTx08_Slide_9.78x22.5mm_W7.62mm_P2.54mm | SW1 |
| 1 | ~{CS} | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP1 |
| 1 | CLK | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP2 |
| 1 | MOSI | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP3 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MISO | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP4 |
| 1 | ~{QW} | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP5 |
| 1 | ~{QRP} | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP6 |
| 1 | ~{CS} | LED_D5.0mm | D1 |
| 1 | MOSI | LED_D5.0mm | D2 |
| 1 | MISO | LED_D5.0mm | D3 |
| 12 | 0.1UF 0.1uF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1, C2, C3, C4, C5, C6, C8, C9 +4 |
| 1 | 0.1UF 220uF | CP_Radial_D6.3mm_P2.50mm | C7 |
| 1 | 0.1UF 100n | C_Disc_D5.0mm_W2.5mm_P5.00mm | C10 |
| 1 | 560 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 180 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 2 | 10K 180 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R4 |
| 1 | 10k | R_Array_SIP9 | RN1 |
Prototype design files
The KiCad project lives in the ifilot/slot-otter repository on GitHub; these links point at the commit this page was built from.
Prototype: common questions
How big is the Prototype PCB?
The Prototype measures 151.6 × 82.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Prototype?
45 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Prototype design files?
From the ifilot/slot-otter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Prototype design in my own project?
The repository has no license, so all rights stay with ifilot. Use it as a reference, and ask the author before reusing the design.