Pedalshield
inktrap·pedalshield·kicad/rev-E/pedal shield.kicad_pcb
About the Pedalshield PCB
Pedalshield is an open source PCB design by inktrap, published on GitHub. It is a 2-layer board measuring 53.3 × 101.6 mm, with 73 components from 34 distinct parts.
Other key parts include the TL072 and TC1044. By type, the board carries 20 resistors, 18 capacitors, 8 test points, 5 diodes, 3 ICs and 3 switches.
It belongs with the audio and dev boards & breakouts designs in this gallery.
From the project
A collection about electrosmash's pedalshield-due
I wanted "my own" overview of pedalshield resources, one that allows for collaboration and forks, and that is always available. So here we go.
- electrosmash site - the most important topics from the electrosmash due forum - howtos (pdf, flickr, youtube)
- hardware analysis - circuit diagram → circuit.png - input/output stages
- BOM (rar) BOM-pedalSHIELD.rar → bom and alternatives - best options to power arduino due - troubleshooting guide
Main components on the Pedalshield
Pedalshield bill of materials (BOM)
73 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | TL072 | DIP-8__300 | U1, U2 |
| 1 | TC1044 | DIP-8__300 | U3 |
| 1 | Guitar_IN | JACK_AUDIO | J1 |
| 1 | OUTPUT | JACK_AUDIO | J2 |
| 5 | CONN_8pins | SIL-8 | CONN2, CONN3, CONN4, CONN5, CONN6 |
| 1 | JUMPER | PIN_ARRAY_2X1 | JP1 |
| 1 | 500K | PIN_ARRAY_3X1 | RV1 |
| 3 | 10K | RVAR | RV2, RV3, RV4 |
| 1 | SWITCH_3PDT | 3PDT | SW1 |
| 1 | SWITCH_INV | SW_SPDT_pedalSHIELD | SW2 |
| 1 | SWITCH_INV | SW_SPDT | SW3 |
| 1 | 3V3 TP | PINTST | TP1 |
| 1 | 1V6 TP | PINTST | TP2 |
| 2 | GND TP | PINTST | TP3, TP6 |
| 1 | +5V TP | PINTST | TP4 |
| 1 | -5V TP | PINTST | TP5 |
| 1 | DAC0 | PINTST | TP7 |
| 1 | DAC1 | PINTST | TP8 |
| 1 | hole1 | 1pin | hole1 |
| 3 | P*** | 1pin | hole2, hole3, hole4 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 1N5817 | D3 | D1, D2, D3, D4 |
| 1 | LED | LED-3MM | D5 |
| 6 | 0.1u | C2 | C1, C4, C6, C7, C10, C11 |
| 5 | 47p | C2 | C2, C5, C8, C9, C12 |
| 1 | 4.7u | C1V5 | C3 |
| 1 | 1u | C1V5 | C13 |
| 2 | 10u | C1V5 | C14, C15 |
| 2 | 100n | C2 | C16, C17 |
| 1 | 47uF | C1V5 | C18 |
| 2 | 10M | R3 | R1, R2 |
| 1 | 1K | R3 | R3 |
| 12 | 100K | R3 | R4, R6, R8, R11, R12, R13, R14, R15 +4 |
| 4 | 4.7K | R3 | R5, R9, R10, R21 |
| 1 | 50K | R3 | R7 |
Pedalshield design files
The KiCad project lives in the inktrap/pedalshield repository on GitHub; these links point at the commit this page was built from.
Pedalshield: common questions
How big is the Pedalshield PCB?
The Pedalshield measures 53.3 × 101.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pedalshield?
73 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pedalshield design files?
From the inktrap/pedalshield repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Pedalshield design in my own project?
The repository has no license, so all rights stay with inktrap. Use it as a reference, and ask the author before reusing the design.
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2k