Stardust
IsaiahBunsley·Stardust·KiCad/Stardust/Stardust.kicad_pcb
About the Stardust PCB
Stardust is an open source ESP32 PCB design by IsaiahBunsley, published on GitHub. It is a 2-layer board measuring 77 × 77 mm, with 37 components from 20 distinct parts.
Its main chip is the ESP32, from the ESP32 family. Other key parts include the BTT TMC2209 V1.3, WEMOS_D1_mini and 56200001009. By type, the board carries 14 resistors, 10 connectors, 6 capacitors, 5 ICs and 2 diodes.
It belongs with the robotics & motion and iot & wireless designs in this gallery.
From the project
Harmonic gear driven equatorial mount for astrophotography.
GOALS: - Achieve sub arcsecond prescision - Make a sleek and nice-to-view body assembly - Use as few pre-made assemblies as possible - Ample wieght capacity ( >10 lbs, ideally >20 lbs ) - Ease of use/control using pre-developed software such as PHD2, OnStep, etc... - Design a PCB to house stepper controllers, microcrontroller, WiFi, etc.. - Efficient homing process - Create a product that is not only good-looking but easy to use and enjoy
Main components on the Stardust
Stardust bill of materials (BOM)
37 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32 | MODULE_ESP32-DEVKITC | U1 |
| 2 | BTT TMC2209 V1.3 | MODULE_TMC2209_SILENTSTEPSTICK | U2, U3 |
| 1 | WEMOS_D1_mini | WEMOS_D1_mini_light | U4 |
| 1 | 56200001009 LittlFuse 2.5 Amp | FuseHolder_RHDR2W53P0X508_1X2 | U8 |
| 1 | 12V DC | DC_PowerConn_694108402002 | J1 |
| 1 | 85513-5002 RJ12 | RJ12_855135114 | J2 |
| 2 | 1x2 Connector | PinHeader_1x02_P2.54mm_Vertical | J3, J7 |
| 2 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J4, J5 |
| 1 | 1x3 Header | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | Conn_01x19_Pin | PinHeader_1x19_P2.54mm_Vertical | J8 |
| 1 | 5V IN | PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | 12V OUT | PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | PWR LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | STATUS LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 4 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6, C8 |
| 1 | 100 uF | 100uFElectrolyticCap_CAPAE830X1080N | C7 |
| 1 | 330nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9 |
| 8 | 4.7K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4, R5, R6, R7, R9, R10 |
| 1 | 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 5 | 2.4K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R13, R14, R15 |
Stardust design files
The KiCad project lives in the IsaiahBunsley/Stardust repository on GitHub; these links point at the commit this page was built from.
Stardust: common questions
What microcontroller does the Stardust use?
The Stardust is built around the ESP32, from the ESP32 family.
How big is the Stardust PCB?
The Stardust measures 77 × 77 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stardust?
37 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Stardust design files?
From the IsaiahBunsley/Stardust repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Stardust design in my own project?
The repository has no license, so all rights stay with IsaiahBunsley. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Stardust without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k