Cubli
ivannasocarras·cubli·cubli_pcb/cubli_pcb.kicad_pcb
About the Cubli PCB
Cubli is an open source ESP32 PCB design by ivannasocarras, published on GitHub. It is a 2-layer board measuring 131.9 × 114.3 mm, with 36 components from 12 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1, from the ESP32 family. Other key parts include the ICM20948_MUSROCK_BREAKOUT. By type, the board carries 14 resistors, 8 capacitors, 6 transistors, 2 ICs, 1 battery holder and 1 switch.
Main components on the Cubli
Cubli bill of materials (BOM)
36 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1 ESP32-S3-DevKitC-1 | ESP32-S3-DevKitC-1 | U1 |
| 1 | ICM20948_MUSROCK_BREAKOUT ICM20948_Remote | TerminalBlock_KF301_1x08_P5.08mm_IMU | U2 |
| 6 | MMBT2222A | SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 1 | Battery | TerminalBlock_KF301_1x02_P5.08mm | BT1 |
| 3 | NIDEC24H_SERVO_MOTOR Nidec24H_Servo_Motor | TerminalBlock_KF301_1x08_P5.08mm | Mx1, My1, Mz1 |
| 1 | MINI560_5V_BUCK Mini560_5V_Buck | Mini560_5V_Buck_Module | PS1 |
| 1 | SW_SPST | TerminalBlock_KF301_1x02_P5.08mm | SW1 |
| 7 | 100NF 100nF | C_0805_2012Metric | C1, C2, C3, C5, C6, C7, C8 |
| 1 | 470UF 470uF | CP_Radial_D8.0mm_P3.50mm | C4 |
| 6 | 2k | R_0805_2012Metric | R1, R3, R5, R7, R9, R11 |
| 7 | 10K 10k | R_0805_2012Metric | R2, R4, R6, R8, R10, R12, R14 |
| 1 | 47K 47k | R_0805_2012Metric | R13 |
Cubli design files
The KiCad project lives in the ivannasocarras/cubli repository on GitHub; these links point at the commit this page was built from.
Cubli: common questions
What microcontroller does the Cubli use?
The Cubli is built around the ESP32-S3-DEVKITC-1, from the ESP32 family.
How big is the Cubli PCB?
The Cubli measures 131.9 × 114.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cubli?
36 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cubli design files?
From the ivannasocarras/cubli repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Cubli design in my own project?
The repository has no license, so all rights stay with ivannasocarras. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Cubli without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k