MUSIC-I-SEE-MUSIC-I-KNOW
jain2008dhairya-hue·MUSIC-I-SEE-MUSIC-I-KNOW
About the MUSIC-I-SEE-MUSIC-I-KNOW PCB
MUSIC-I-SEE-MUSIC-I-KNOW is an open source Raspberry Pi PCB design by jain2008dhairya-hue, published on GitHub. It is a board, with 13 components from 12 distinct parts.
Its main chip is the Raspberry Pi Zero 2 W, from the Raspberry Pi family. Other key parts include the 2.4in ILI9341 SPI LCD, PCM5102A DAC module, MPR121 breakout, TP4056 charger (protected) and MT3608 boost (set 5.1V). By type, the board carries 6 ICs, 2 resistors, 1 connector, 1 battery holder, 1 switch and 1 capacitor.
It belongs with the audio, power & battery and displays & leds designs in this gallery.
From the project
JUST A BEGINNER LEVEL MUSIC +ELECTRONIC PROJECT
A pocket music player in the shape of a classic iPod, built from a Raspberry Pi Zero 2 W, a 2.4" colour display, an I2S DAC and a custom touch click wheel, in a 3D printed case. Target cost is under ₹10,000 (about $100), not counting printing.
The iPod's click wheel is still one of the nicest ways to browse music. I wanted to see how close hobbyist parts get to it: the same screen resolution as the iPod Classic (320x240), a wheel you scroll with your thumb, and proper DAC audio instead of the Pi's noisy built-in output.
Main components on the MUSIC-I-SEE-MUSIC-I-KNOW
MUSIC-I-SEE-MUSIC-I-KNOW bill of materials (BOM)
13 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Raspberry Pi Zero 2 W | U1 | |
| 1 | 2.4in ILI9341 SPI LCD | U2 | |
| 1 | PCM5102A DAC module | U3 | |
| 1 | MPR121 breakout | U4 | |
| 1 | TP4056 charger (protected) | U5 | |
| 1 | MT3608 boost (set 5.1V) | U6 | |
| 1 | USB-C breakout | J2 | |
| 1 | LiPo 103040 3.7V 1200mAh | BT1 | |
| 1 | Power switch | SW1 | |
| 1 | Touch wheel PCB (custom) | WHEEL1 | |
| 1 | 470uF | C1 | |
| 2 | 5.1k | R1, R2 |
MUSIC-I-SEE-MUSIC-I-KNOW design files
The KiCad project lives in the jain2008dhairya-hue/MUSIC-I-SEE-MUSIC-I-KNOW repository on GitHub; these links point at the commit this page was built from.
- Schematicdiy_ipod.kicad_sch
- BOMBOM.csv
MUSIC-I-SEE-MUSIC-I-KNOW: common questions
What microcontroller does the MUSIC-I-SEE-MUSIC-I-KNOW use?
The MUSIC-I-SEE-MUSIC-I-KNOW is built around the Raspberry Pi Zero 2 W, from the Raspberry Pi family.
How many components are on the MUSIC-I-SEE-MUSIC-I-KNOW?
13 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MUSIC-I-SEE-MUSIC-I-KNOW design files?
From the jain2008dhairya-hue/MUSIC-I-SEE-MUSIC-I-KNOW repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the MUSIC-I-SEE-MUSIC-I-KNOW design in my own project?
The repository has no license, so all rights stay with jain2008dhairya-hue. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MUSIC-I-SEE-MUSIC-I-KNOW without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507