Blare
jdszekeres·blare·PCB/blare.kicad_pcb
About the Blare PCB
Blare is an open source ESP32 PCB design by jdszekeres, published on GitHub. It is a 2-layer board measuring 100 × 58.5 mm, with 7 components from 4 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 4 switches, 1 IC, 1 connector and 1 buzzer.
It belongs with the keyboards, iot & wireless and sensors designs in this gallery.
From the project
An Alarm Clock for the Hack Club Blare YSWS. It contains references to the Monty Python's Flying Circus Dead Parrot Sketch
An Alarm Clock for the Hack Club Blare YSWS. It contains references to the Monty Python's Flying Circus Dead Parrot Sketch
The PCB is designed and created in KiCad. It uses a: - Seeed Studio ESP 32 C3 - generic buzzer - 2.25 in TFT Screen - 4 keyswitches
Key Challenges: single threaded processing, storage space constraints, robust wifi fallbacks

Main components on the Blare
Blare bill of materials (BOM)
7 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-DIP | U1 |
| 1 | Conn_01x08_Pin | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 4 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4 |
Blare design files
The KiCad project lives in the jdszekeres/blare repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/blare.kicad_pcb
- SchematicPCB/blare.kicad_sch
Blare: common questions
What microcontroller does the Blare use?
The Blare is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Blare PCB?
The Blare measures 100 × 58.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Blare?
7 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the Blare design files?
From the jdszekeres/blare repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Blare design in my own project?
The repository has no license, so all rights stay with jdszekeres. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Blare without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k