Digital Board Rev 2

jer-lil·tremolo-hardware·Rev_2/Digital Board Rev 2/Digital Board Rev 2.kicad_pcb

Digital Board Rev 2 layout, top view — open source STM32 board by jer-lil

About the Digital Board Rev 2

Digital Board Rev 2 is an open source STM32 PCB design by jer-lil, published on GitHub. It is a 4-layer board measuring 59.5 × 96.3 mm, with 86 components from 59 distinct parts.

Its main chip is the FT230XS-R, from the STM32 family. Other key parts include the TLP222A-2, NCP1117DT33RKG and TC7662Bx0A. By type, the board carries 26 capacitors, 18 resistors, 15 connectors, 7 diodes, 4 ICs and 3 switches.

It belongs with the audio designs in this gallery.

From the project

This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main

This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main

This tremolo packs a lot of features into a very small (Hammond 125B, 65x120mm) enclosure. Features include:

- All analog signal path - Full stereo, with dedicated 1/4" jacks - Harmonic tremolo - Continually adjustable LFO phase, allowing for sounds between mono/stereo/harmonic not found in other tremolo pedals (that I've discovered, please let me know if you know of any) - Envelope control -…

Main components on the Digital Board Rev 2

Digital Board Rev 2 bill of materials (BOM)

86 components, 59 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
FT230XS-R
STM32F303R6Tx
U1
1
TLP222A-2
U26
1
NCP1117DT33RKG
NCP1117-3.3_SOT223
U27
1
TC7662Bx0A
U28
1
BSS83P
Q1
1
MMBT3904
Q25
1
8MHz
Y1
2
Conn_01x02_Male
J1, J2
1
Conn_01x06_Male
J3
1
Conn_01x08_Female
J4
2
AudioJack3_Switch
J5, J10
4
CONN_01X02_MALE
AudioJack3_Switch
J6, J7, J8, J9
1
Conn_01x10_Female
J11
1
Barrel_Jack
J12
1
CON_01X02_PTH_2.54MM
Conn_01x06_Female
J13
1
CON_01X04_PTH_2.54MM
Conn_01x06_Female
J14
1
Conn_01x03_Male
J15
1
Polyfuse
F1
1
IM05
K1
5
10K
R_POT_TRIM
RV1, RV2, RV3, RV4, RV5
Show 39 more
QtyPartRefs
2
100k
RV8, RV9
1
R_POT_TRIM
RV10
2
CON_01X02_PTH_2.54MM
SW_SPDT_MSM
SW1, SW2
1
SW_SPDT_MSM
SW3
1
DIODES_B140_SMA
LED_RGBA
D1
1
LED_RGBA
D2
1
LED_SINGLE-0603-GREEN
B120-E3
D3
1
LED_SINGLE-0603-GREEN
LED_Small
D4
1
LED_Small
D5
1
DDZ10CSF-7
D_Zener
D6
1
LED_SINGLE-0805-RED
LED_Small
D7
1
1UF
4.7u
C1
2
0.1UF
18p
C2, C3
3
10UF
100n
C4, C5, C6
5
0.1UF
100n
C7, C8, C16, C17, C20
1
0.1UF
10n
C9
1
10N
1u
C10
1
1UF
100nF
C11
3
0.1UF
100nF
C12, C13, C14
1
100N
100nF
C15
2
0.1UF
470n
C18, C19
1
0.1UF
10u
C21
1
100N
10u
C22
2
100N
100uF
C23, C24
1
100uF
C25
1
100nF
C26
1
560
10k
R1
2
330
R2, R3
1
470
330
R4
2
100
330
R5, R11
3
100
1k
R6, R7, R12
1
100
10k
R8
1
10K
19.1k
R9
1
10K
330
R10
1
2.2k
R50
1
1k
R51
1
470
R52
2
630
R53, R54
1
R_Pack08
RN1

Digital Board Rev 2 design files

The KiCad project lives in the jer-lil/tremolo-hardware repository on GitHub; these links point at the commit this page was built from.

Digital Board Rev 2: common questions

What microcontroller does the Digital Board Rev 2 use?

The Digital Board Rev 2 is built around the FT230XS-R, from the STM32 family.

How big is the Digital Board Rev 2?

The Digital Board Rev 2 measures 59.5 × 96.3 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Digital Board Rev 2?

86 components, from 59 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Digital Board Rev 2 design files?

From the jer-lil/tremolo-hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Digital Board Rev 2 design in my own project?

The repository has no license, so all rights stay with jer-lil. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Digital Board Rev 2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in tremolo-hardware

Similar boards