17 open source boards using the FT230XS-R

Real designs built with the FT230XS-R, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the FT230XS-R

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the FT230XS-R connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 10 of 11 designs, most often 100 nF (then 4.7 µF).
  • The USBDP pin has a series resistor on 9 of 12 designs, most often 27 Ω (then 33 Ω).
  • The USBDM pin has a series resistor on 9 of 11 designs, most often 27 Ω (then 33 Ω).
  • The CBUS3 pin is left unconnected on 8 of 11 designs (a signal on 2).
VCCIOpin 3Connected to: 3.3V 58% · a signal 42%
  • Decoupling capacitor on 50% · 100 nF (6), 4.7 µF (2)
GNDpin 5, 13Connected to: GND 100%
CBUS2pin 7Connected to: Signal 83% · not connected 17%
  • Series resistor on 33% · 1 kΩ (3), 270 Ω (1)
USBDPpin 8Connected to: Signal 92%
  • Series resistor on 75% · 27 Ω (8), 33 Ω (1)
USBDMpin 9Connected to: Signal 100%
  • Series resistor on 82% · 27 Ω (8), 33 Ω (1)
VCCpin 12Connected to: 5V 64% · a signal 36%
  • Decoupling capacitor on 91% · 100 nF (9), 4.7 µF (4), 10 µF (2)
CBUS1pin 14Connected to: Signal 82% · not connected 18%
  • Series resistor on 36% · 1 kΩ (3), 270 Ω (1)
CBUS0pin 15Connected to: Not connected 64% · a signal 36%
CBUS3pin 16Connected to: Not connected 73% · a signal 18%

6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Backpack by osrf, Arduino Tracking Antenna by UWARG, IsoUSBRS422 by alperyazar and SDA-Wonder System Board by stanislavbrtna.

The FT230XS-R in open source designs

The gallery holds 17 open source boards using the FT230XS-R from 12 GitHub repositories; a typical one measures about 80 × 96.3 mm and carries around 86 components.

65% use four copper layers or more, and 29% carry an open source license.

The most starred is Backpack by osrf.

Parts used alongside the FT230XS-R

Microcontrollers on boards using the FT230XS-R

FT230XS-R: common questions

Where can I find a FT230XS-R reference design?

Each of the 17 boards on this page is a real design using the FT230XS-R. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the FT230XS-R VCC pin?

The VCC pin has a decoupling capacitor on 10 of 11 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 12 open source designs using the FT230XS-R.

What resistor goes on the FT230XS-R USBDP pin?

The USBDP pin has a series resistor on 9 of 12 designs, most often 27 Ω (then 33 Ω). Counted from the KiCad layouts of 12 open source designs using the FT230XS-R.

What resistor goes on the FT230XS-R USBDM pin?

The USBDM pin has a series resistor on 9 of 11 designs, most often 27 Ω (then 33 Ω). Counted from the KiCad layouts of 12 open source designs using the FT230XS-R.

Which microcontrollers do boards using the FT230XS-R use?

Most are built on STM32 (7), ESP32 (3), RP2040/RP2350 (2) and TI MSP430/CC (1).

How big is a typical board using the FT230XS-R?

The median is 80 × 96.3 mm, and 35% are two-layer designs.

What is the most popular open source board using the FT230XS-R?

By GitHub stars, Backpack by osrf, with 207 stars.

Can I simulate one of these boards using the FT230XS-R before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part