Digital Board Rev 1
jer-lil·tremolo-hardware·Rev_1/Digital_Board_Rev_1/Digital_Board_Rev_1.kicad_pcb
About the Digital Board Rev 1
Digital Board Rev 1 is an open source STM32 PCB design by jer-lil, published on GitHub. It is a 4-layer board measuring 101.6 × 101.6 mm, with 85 components from 34 distinct parts.
Its main chip is the STM32F030RCT6TR, from the STM32 family. Other key parts include the FT230XS-R, NCP1117LPST33T3G, MCP42050, NPN_BJTMMBT3904_SOT-23-3 and NSL-32. By type, the board carries 24 capacitors, 23 resistors, 15 ICs, 9 diodes, 3 connectors and 3 LEDs.
It belongs with the audio designs in this gallery.
From the project
This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main
This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main
This tremolo packs a lot of features into a very small (Hammond 125B, 65x120mm) enclosure. Features include:
- All analog signal path - Full stereo, with dedicated 1/4" jacks - Harmonic tremolo - Continually adjustable LFO phase, allowing for sounds between mono/stereo/harmonic not found in other tremolo pedals (that I've discovered, please let me know if you know of any) - Envelope control -…
Main components on the Digital Board Rev 1
Digital Board Rev 1 bill of materials (BOM)
85 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FT230XS-R | MF_IC_Digital-SSOP16 | U1 |
| 1 | NCP1117LPST33T3G | MF_IC_Power-SOT-223-3 | U2 |
| 2 | MCP42050 | TSSOP-14-1EP_4.4x5mm_P0.65mm | U3, U4 |
| 4 | NPN_BJTMMBT3904_SOT-23-3 | MF_Discrete_Semiconductor-SOT-23-3 | U5, U6, U9, U10 |
| 4 | NSL-32 | Luna_NSL-32 | U7, U8, U11, U12 |
| 1 | STM32F030RCT6TR STM32F030RCTx | LQFP-64_10x10mm_P0.5mm | U13 |
| 2 | CPC1017N | SOP-4_3.8x4.1mm_P2.54mm | U14, U15 |
| 1 | USB_MICRO_RIGHT | MF_Connectors-MICROUSB-RIGHT | J1 |
| 1 | AUDIOJACK3_SWITCH AudioJack3_Switch | Jack_0.25in_TRS_Switched | J20 |
| 1 | Barrel_Jack | BarrelJack_CUI_PJ-063AH_Horizontal_CircularHoles | J21 |
| 6 | 10K 10k | Potentiometer_Alpha_RD901F-40-00D_Single_Vertical_CircularHoles | RV1, RV2, RV3, RV4, RV5, RV6 |
| 1 | CON_01X02_PTH_2.54MM SW_DIP_x04 | SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW1 |
| 1 | CON_01X02_PTH_2.54MM SW_DIP_x02 | SW_DIP_SPSTx02_Slide_9.78x7.26mm_W7.62mm_P2.54mm | SW2 |
| 1 | LED_SINGLE-0603-GREEN | MF_LEDs-LED0603 | 3V3 |
| 1 | LED_SINGLE-0805-GREEN | MF_LEDs-LED0805 | LED1 |
| 1 | LED_SINGLE-0805-RED | MF_LEDs-LED0805 | LED2 |
| 2 | DIODES_B140_SMA | MF_Discrete_Semiconductor-SMA | D1, D13 |
| 2 | LED_SINGLE-0603-GREEN | MF_LEDs-LED0603 | D3, D4 |
| 4 | LED_SINGLE-0805-RED | MF_LEDs-LED0805 | D6, D7, D8, D9 |
| 1 | LED_RGB_CA_PLCC4 | MF_LEDs-PLCC4 | D10 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 1UF 1uF | MF_Passives-C0402 | C1, C11 |
| 14 | 0.1UF 0.1uF | MF_Passives-C0402 | C2, C3, C7, C8, C9, C12, C13, C14 +6 |
| 3 | 10UF 10uF | MF_Passives-C1206 | C4, C5, C6 |
| 1 | 10N 10n | MF_Passives-C0402 | C10 |
| 4 | 100N 100n | MF_Passives-C0402 | C15, C22, C23, C24 |
| 1 | 560 | MF_Passives-R0402 | R1 |
| 2 | 330 | MF_Passives-R0402 | R2, R3 |
| 1 | 470 | MF_Passives-R0402 | R4 |
| 8 | 100 | MF_Passives-R0603 | R5, R6, R7, R8, R11, R12, R13, R14 |
| 4 | 10K 10k | MF_Passives-R0603 | R9, R10, R15, R16 |
| 1 | 10K 10k | MF_Passives-R0402 | R17 |
| 1 | 0 | MF_Passives-R0603 | R18 |
| 3 | 100 | MF_Passives-R0402 | R25, R26, R27 |
| 2 | 47 | MF_Passives-R0402 | R28, R29 |
Digital Board Rev 1 design files
The KiCad project lives in the jer-lil/tremolo-hardware repository on GitHub; these links point at the commit this page was built from.
Digital Board Rev 1: common questions
What microcontroller does the Digital Board Rev 1 use?
The Digital Board Rev 1 is built around the STM32F030RCT6TR, from the STM32 family.
How big is the Digital Board Rev 1?
The Digital Board Rev 1 measures 101.6 × 101.6 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Digital Board Rev 1?
85 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Digital Board Rev 1 design files?
From the jer-lil/tremolo-hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Digital Board Rev 1 design in my own project?
The repository has no license, so all rights stay with jer-lil. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Digital Board Rev 1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in tremolo-hardware
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k