Digital Board Rev3
jer-lil·tremolo-hardware·Rev_3/Digital_Board_Rev_3/Digital_Board_Rev3.kicad_pcb
About the Digital Board Rev3
Digital Board Rev3 is an open source STM32 PCB design by jer-lil, published on GitHub. It is a 4-layer board measuring 59.5 × 96.3 mm, with 86 components from 59 distinct parts.
Its main chip is the FT230XS-R, from the STM32 family. Other key parts include the TLP222A-2, NCP1117DT33RKG and TC7662Bx0A. By type, the board carries 26 capacitors, 18 resistors, 15 connectors, 7 diodes, 4 ICs and 3 switches.
It belongs with the audio designs in this gallery.
From the project
This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main
This is the hardware (PCB, MCAD) design for a tremolo pedal for guitar (or bass, synth, tonewheel organ, whatever you like). The firmware is here: https://github.com/jer-lil/tremolo-firmware/tree/main
This tremolo packs a lot of features into a very small (Hammond 125B, 65x120mm) enclosure. Features include:
- All analog signal path - Full stereo, with dedicated 1/4" jacks - Harmonic tremolo - Continually adjustable LFO phase, allowing for sounds between mono/stereo/harmonic not found in other tremolo pedals (that I've discovered, please let me know if you know of any) - Envelope control -…
Main components on the Digital Board Rev3
Digital Board Rev3 bill of materials (BOM)
86 components, 59 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FT230XS-R STM32F303R6Tx | LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TLP222A-2 | DIP-8_W7.62mm | U26 |
| 1 | NCP1117DT33RKG NCP1117-3.3_SOT223 | SOT-223-3_TabPin2 | U27 |
| 1 | TC7662Bx0A | SOIC-8_3.9x4.9mm_P1.27mm | U28 |
| 1 | BSS83P | SOT-23 | Q1 |
| 1 | MMBT3904 | SOT-23 | Q25 |
| 1 | 8MHz | Crystal_HC49-U_Vertical | Y1 |
| 2 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical | J1, J2 |
| 1 | Conn_01x06_Male | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_01x08_Female | PinSocket_1x08_P2.54mm_Vertical | J4 |
| 2 | AudioJack3_Switch | Jack_0.25in_TRS_Switched | J5, J10 |
| 4 | CONN_01X02_MALE AudioJack3_Switch | Jack_0.25in_TRS_Switched | J6, J7, J8, J9 |
| 1 | Conn_01x10_Female | PinSocket_1x10_P2.54mm_Vertical | J11 |
| 1 | Barrel_Jack | BarrelJack_CUI_PJ-063AH_Horizontal_CircularHoles | J12 |
| 1 | CON_01X02_PTH_2.54MM Conn_01x06_Female | PinSocket_1x06_P2.54mm_Vertical | J13 |
| 1 | CON_01X04_PTH_2.54MM Conn_01x06_Female | PinSocket_1x06_P2.54mm_Vertical | J14 |
| 1 | Conn_01x03_Male | PinHeader_1x03_P2.54mm_Vertical | J15 |
| 1 | Polyfuse | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | IM05 | Relay_DPDT_NL_TE_IM05GR | K1 |
| 5 | 10K R_POT_TRIM | Potentiometer_9MM | RV1, RV2, RV3, RV4, RV5 |
Show 39 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 100k | Potentiometer_Bourns_3314G_Vertical | RV8, RV9 |
| 1 | R_POT_TRIM | Potentiometer_9MM | RV10 |
| 2 | CON_01X02_PTH_2.54MM SW_SPDT_MSM | SW_Toggle_SPDT | SW1, SW2 |
| 1 | SW_SPDT_MSM | SW_Toggle_SPDT | SW3 |
| 1 | DIODES_B140_SMA LED_RGBA | LED_D5.0mm-4_RGB | D1 |
| 1 | LED_RGBA | LED_D5.0mm-4_RGB | D2 |
| 1 | LED_SINGLE-0603-GREEN B120-E3 | D_SMA | D3 |
| 1 | LED_SINGLE-0603-GREEN LED_Small | LED_0805_2012Metric_Castellated | D4 |
| 1 | LED_Small | LED_0805_2012Metric_Castellated | D5 |
| 1 | DDZ10CSF-7 D_Zener | D_SMA_Handsoldering | D6 |
| 1 | LED_SINGLE-0805-RED LED_Small | LED_0805_2012Metric_Castellated | D7 |
| 1 | 1UF 4.7u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 2 | 0.1UF 18p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 3 | 10UF 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6 |
| 5 | 0.1UF 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8, C16, C17, C20 |
| 1 | 0.1UF 10n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 1 | 10N 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 1UF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11 |
| 3 | 0.1UF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12, C13, C14 |
| 1 | 100N 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C15 |
| 2 | 0.1UF 470n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18, C19 |
| 1 | 0.1UF 10u | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C21 |
| 1 | 100N 10u | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C22 |
| 2 | 100N 100uF | CP_Radial_D5.0mm_P2.00mm | C23, C24 |
| 1 | 100uF | CP_Radial_D5.0mm_P2.00mm | C25 |
| 1 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C26 |
| 1 | 560 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 2 | 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 1 | 470 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 2 | 100 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R11 |
| 3 | 100 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7, R12 |
| 1 | 100 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | 10K 19.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 1 | 10K 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 2.2k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R50 |
| 1 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R51 |
| 1 | 470 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R52 |
| 2 | 630 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R53, R54 |
| 1 | R_Pack08 | R_Array_Convex_8x0602 | RN1 |
Digital Board Rev3 design files
The KiCad project lives in the jer-lil/tremolo-hardware repository on GitHub; these links point at the commit this page was built from.
Digital Board Rev3: common questions
What microcontroller does the Digital Board Rev3 use?
The Digital Board Rev3 is built around the FT230XS-R, from the STM32 family.
How big is the Digital Board Rev3?
The Digital Board Rev3 measures 59.5 × 96.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Digital Board Rev3?
86 components, from 59 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Digital Board Rev3 design files?
From the jer-lil/tremolo-hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Digital Board Rev3 design in my own project?
The repository has no license, so all rights stay with jer-lil. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Digital Board Rev3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in tremolo-hardware
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k