EV-BMS-Cell-Protection
jimchantes·EV-BMS-Cell-Protection·Hardware/EV-BMS-Cell-Protection.kicad_pcb
About the EV-BMS-Cell-Protection PCB
EV-BMS-Cell-Protection is an open source PCB design by jimchantes, published on GitHub under the MIT license. It is a 2-layer board measuring 6 × 13.8 mm, with 6 components from 6 distinct parts.
Other key parts include the LM393. By type, the board carries 4 resistors, 1 IC and 1 connector.
It belongs with the power & battery designs in this gallery.
From the project
An overvoltage and undervoltage monitoring circuit (Window Comparator) designed for a Formula Student EV Li-Ion battery pack.
An overvoltage and undervoltage monitoring circuit (BMS/AMS aspect) designed for a Formula Student Electric Vehicle (EV). The circuit monitors a single lithium-ion cell, ensuring it stays within the safe operating window of 3.0V to 4.2V. If the cell voltage violates these parameters, the system triggers a 0V Fault Signal to open the safety shutdowns.
Result: The simulation confirms a sharp, deterministic transition to 0V whenever the swept input voltage falls below 3.0V or exceeds 4.2V.
Main components on the EV-BMS-Cell-Protection
EV-BMS-Cell-Protection bill of materials (BOM)
6 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM393 | DIP-8_W7.62mm | U1 |
| 1 | Conn_01x04_Pin | PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | 10kΩ | R_0805_2012Metric | R1 |
| 1 | 1.6kΩ | R_0805_2012Metric | R2 |
| 1 | 2.4kΩ | R_0805_2012Metric | R3 |
| 1 | 6kΩ | R_0805_2012Metric | R4 |
EV-BMS-Cell-Protection design files
The KiCad project lives in the jimchantes/EV-BMS-Cell-Protection repository on GitHub; these links point at the commit this page was built from.
EV-BMS-Cell-Protection: common questions
How big is the EV-BMS-Cell-Protection PCB?
The EV-BMS-Cell-Protection measures 6 × 13.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the EV-BMS-Cell-Protection?
6 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the EV-BMS-Cell-Protection design files?
From the jimchantes/EV-BMS-Cell-Protection repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the EV-BMS-Cell-Protection design in my own project?
Yes, under the terms of its MIT license, which jimchantes chose for the repository.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k