232 open source boards using the LM393
Real designs built with the LM393, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687AVR/Arduino
Smu main 1
jaromir-sukuba
130 × 80 mm206 parts2LNo license188STM32
VNA
profdc9
100 × 85 mm178 parts2LNo license92NXP
Precharge
michaelruppe
133 × 98 mm110 parts2LMIT56Sk162-herd mixer
mirdej
104.3 × 106.8 mm223 parts4LNo license47Bluetooth minidisc
17o2
72.4 × 44.5 mm71 parts4LNo license44AVR/Arduino
Entropy32-Plus
captainchapster
53 × 63 mm34 parts2LMIT37C6021light
GBert
100 × 50 mm74 parts2LNo license36Dragon64
danwerner21
333.2 × 205.9 mm220 parts2LNo license34SimpleModem
AndersBNielsen
46.7 × 15.2 mm34 parts2LCC-BY-NC-4.027NXP
Core64 LB v0.6
ageppert
85 × 170 mm136 parts2LGPL-3.016Raspberry Pi
PiUPS
diminDDL
87.4 × 56 mm110 parts2LCERN-OHL-W-2.015A2C DVI Board
FarLeftLane
31.5 × 79.5 mm13 parts2LMIT12FlippyDriver
NietoSkunk
189.4 × 59.1 mm310 parts4LMIT10ESP8266
Flight controller v2
Eryk-Mozdzen
45 × 89 mm108 parts4LNo license9AVR/Arduino
AT65C02 Hobby Computer
Kayto
241.3 × 149.9 mm161 parts2LCERN-OHL-1.27NXP
Precharge
LSUTigerRacing
133 × 98 mm113 parts2LNo license7AVR/Arduino
Usbkbdshield vt100
ryu10
68.6 × 53.2 mm29 parts2LNo license7Air quality sensor-MQ135-breakout hardware design
SolderedElectronics
22 × 38 mm12 parts2LTAPR-OHL-1.07- schematic only · 71 parts
G3-Personality-Card-USB
croissantking
71 partsCC0-1.07 Raspberry Pi
Battmanpi
andrewerrington
65 × 56 mm76 parts2LGPL-3.06AzizLight
devttys0
70.1 × 29.2 mm55 parts2LNo license6Protectionckt sc
Sougata0204
40.5 × 47 mm26 parts2LMIT6Solarinverter
cpipero
373 × 132.3 mm370 parts2LCC0-1.05FreeDSP-CLASSIC-SMD-B
freeDSP
67.3 × 92.3 mm170 parts2LCC-BY-SA-4.05Hardware
xtarke
135.8 × 56.2 mm84 parts2LGPL-3.05Hardware
xtarke
135.8 × 56.2 mm84 parts2LNo license5C6021light
deltaphi
100 × 50 mm74 parts2LGPL-3.05CO-sensor-MQ7-breakout hardware design
SolderedElectronics
22 × 38 mm12 parts2LTAPR-OHL-1.05Northstar HD-5
abzman
190.6 × 172.4 mm154 parts2LUnlicense4AVR/Arduino
RTB C02
git4dcc
75.7 × 36.8 mm81 parts4LApache-2.04FullCapacitorBankAdapter
gongminmin
116.8 × 61 mm43 parts2LMIT4ESP32
TSAL G V4 2
HKUST-Red-Bird-Racing-EVRT
140 × 60 mm117 parts2LNo license3Current Sensing
nyu-rdt
132 × 94.5 mm98 parts2LNo license3EduRoMAA-EduCIAA
ciiiutnfrc
103 × 80 mm73 parts2LGPL-3.03AVR/Arduino
RPM-counter
midasgossye
68.9 × 23 mm62 parts2LNo license3
How designs wire the LM393
Read from the KiCad layouts of 169 open source designs, one per repository: what each pin of the LM393 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 156 of 168 designs (-15V on 4, a signal on 8).
- The 1_OUT pin has a pull-up to 5V on 123 of 169 designs, most often 10 kΩ (then 1 kΩ).
- The 1_OUT pin has a series resistor on 106 of 169 designs, most often 2.2 kΩ (then 1 kΩ).
- The V+ pin has a decoupling capacitor on 105 of 167 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1_OUTpin 1 | Connected to: Signal 97% |
|
| -pin 2, 6 | Connected to: Signal 70% · not connected 16% |
|
| +pin 3, 5 | Connected to: Signal 72% · not connected 16% |
|
| V-pin 4 | Connected to: GND 93% | — |
| 2_OUTpin 7 | Connected to: Signal 54% · not connected 45% |
|
| V+pin 8 | Connected to: 5V 86% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Snark barker by schlae, Smu main 1 by jaromir-sukuba, All in One Railroad Interface by GBert and VNA by profdc9.
The LM393 in open source designs
The gallery holds 232 open source boards using the LM393 from 180 GitHub repositories; a typical one measures about 84.4 × 68.7 mm and carries around 65 components.
84% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is Snark barker by schlae.
Parts used alongside the LM393
Microcontrollers on boards using the LM393
What boards using the LM393 are built for
LM393: common questions
Where can I find a LM393 reference design?
Each of the 232 boards on this page is a real design using the LM393. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM393 V- pin connected?
The V- pin is tied to GND on 156 of 168 designs (-15V on 4, a signal on 8). Counted from the KiCad layouts of 169 open source designs using the LM393.
What pull-up resistor is used on the LM393 1_OUT pin?
The 1_OUT pin has a pull-up to 5V on 123 of 169 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 169 open source designs using the LM393.
What decoupling capacitors do designs use on the LM393 V+ pin?
The V+ pin has a decoupling capacitor on 105 of 167 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 169 open source designs using the LM393.
What parts are used alongside the LM393?
The MQ-X, AMS1117-3.3, LM324, L7805 and PC817 appear in the most repositories here.
Which microcontrollers do boards using the LM393 use?
Most are built on AVR/Arduino (26), ESP32 (17), RP2040/RP2350 (14) and STM32 (13).
How big is a typical board using the LM393?
The median is 84.4 × 68.7 mm, and 84% are two-layer designs.
What is the most popular open source board using the LM393?
By GitHub stars, Snark barker by schlae, with 687 stars.
Can I simulate one of these boards using the LM393 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.